700r4, 1-2 shift at 2500-3000 rpm
#1
Member
Thread Starter
Join Date: Oct 2005
Location: Dallas Texas
Posts: 150
Received 0 Likes
on
0 Posts
Car: 83 Z28, 88 Iroc
Engine: 305 CFI, 350 TPI
Transmission: 700R4, 700R4
Axle/Gears: 3.73
700r4, 1-2 shift at 2500-3000 rpm
I suck when it comes to troubleshooting Transmissions and my knowledge is limited.
This is a stock rebuilt 700r4 transmission I bought and had installed at a transmission shop 6 months, and 4 thousand miles ago. (Take it to the shop have them look at it...) Way ahead of you guys, I will... but first I want a general idea of what might be happening...
The car revs up to about 2500 to 3000 rpm before first shifts to second, after that all my other gears shift fine it seems. The searches for the forums are a bit on the crap side these last couple of weeks...
Another question I have, is it common for stock 700r4 to over rev and not shift correctly (get stuck) when you gun it?
This is a stock rebuilt 700r4 transmission I bought and had installed at a transmission shop 6 months, and 4 thousand miles ago. (Take it to the shop have them look at it...) Way ahead of you guys, I will... but first I want a general idea of what might be happening...
The car revs up to about 2500 to 3000 rpm before first shifts to second, after that all my other gears shift fine it seems. The searches for the forums are a bit on the crap side these last couple of weeks...
Another question I have, is it common for stock 700r4 to over rev and not shift correctly (get stuck) when you gun it?
Last edited by tyrvidar; 10-03-2007 at 01:50 PM.
#2
Supreme Member
Join Date: Jul 2005
Location: North Central Mass.
Posts: 2,123
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1985 Berlinetta
Engine: Megasquirted TPI
Transmission: Transgo 700R4
Axle/Gears: 3.42
Re: 700r4, 1-2 shift at 2500-3000 rpm
What throttle position do you test at?
#3
Member
Thread Starter
Join Date: Oct 2005
Location: Dallas Texas
Posts: 150
Received 0 Likes
on
0 Posts
Car: 83 Z28, 88 Iroc
Engine: 305 CFI, 350 TPI
Transmission: 700R4, 700R4
Axle/Gears: 3.73
Re: 700r4, 1-2 shift at 2500-3000 rpm
I gun it a little bit to about 40-50% + (my guess) it it will shoot up to 2500-3k sit there for a second then it shifts(Shifts fine, no clunking or anything). If I am cruising around my work area (speed bumps blah blah) I don't open it as much (maybe 20-30% or so) which takes it to about 2k-1750 and shifts fine at that point as well (after it sits there for a second or 2, almost like it is building up pressure?)... Any ideas?
Last edited by tyrvidar; 10-03-2007 at 02:48 PM.
#4
Member
Thread Starter
Join Date: Oct 2005
Location: Dallas Texas
Posts: 150
Received 0 Likes
on
0 Posts
Car: 83 Z28, 88 Iroc
Engine: 305 CFI, 350 TPI
Transmission: 700R4, 700R4
Axle/Gears: 3.73
Re: 700r4, 1-2 shift at 2500-3000 rpm
2nd Gear is slipping, dropped it off this morning. Fun stuff
#5
Senior Member
iTrader: (4)
Join Date: Mar 2007
Location: Tallahassee, Florida
Posts: 860
Likes: 0
Received 0 Likes
on
0 Posts
Car: '86 Trans Am and '03 S-10
Engine: 355ci and 4.3l
Transmission: 700R4 and NV3500
Axle/Gears: 7.625/3.42 Auburn and 8.5/3.08 Gov-
Re: 700r4, 1-2 shift at 2500-3000 rpm
1st I would check for correct TV cable adjustment. But there might be a sticking valve in the VBody.
Thread
Thread Starter
Forum
Replies
Last Post
TheTraut88
Engine/Drivetrain/Suspension Parts for Sale
1
09-07-2015 05:22 PM