How long for ECU to relearn?
#1
Senior Member
Thread Starter
Join Date: Feb 2009
Location: Brisbane, Australia
Posts: 863
Likes: 0
Received 15 Likes
on
13 Posts
Car: 1985 Pontiac TransAM
Engine: 400SBC 24x conversion
Transmission: T700r Stage2 Shiftkitted
Axle/Gears: 2.77 9 Bolt
How long for ECU to relearn?
How long does it take the ECU after being reset to re-learn whatever it has?
I pulled the ecu on my 350TPI to check it was working fine, and at the same time changed the SES bulb, plugged it all back in and got code 12 when running shorted diagnostic pins.
Turned the car off, removed wire and started it and left it for 5 mins, and turned it off. That was yesterday, and then today I went for a drive down the road, only about a mile or two, and the throttle repsonse sucked ***. The car drove like a had a caravan in tow.
Is this because the ECU needs to take more readings etc? or is the problem elsewhere?
I pulled the ecu on my 350TPI to check it was working fine, and at the same time changed the SES bulb, plugged it all back in and got code 12 when running shorted diagnostic pins.
Turned the car off, removed wire and started it and left it for 5 mins, and turned it off. That was yesterday, and then today I went for a drive down the road, only about a mile or two, and the throttle repsonse sucked ***. The car drove like a had a caravan in tow.
Is this because the ECU needs to take more readings etc? or is the problem elsewhere?
#2
Senior Member
Join Date: Mar 2008
Location: nj
Posts: 428
Likes: 0
Received 0 Likes
on
0 Posts
Car: 89 iroc
Engine: l98
Transmission: tremec
Re: How long for ECU to relearn?
How long does it take the ECU after being reset to re-learn whatever it has?
I pulled the ecu on my 350TPI to check it was working fine, and at the same time changed the SES bulb, plugged it all back in and got code 12 when running shorted diagnostic pins.
Turned the car off, removed wire and started it and left it for 5 mins, and turned it off. That was yesterday, and then today I went for a drive down the road, only about a mile or two, and the throttle repsonse sucked ***. The car drove like a had a caravan in tow.
Is this because the ECU needs to take more readings etc? or is the problem elsewhere?
I pulled the ecu on my 350TPI to check it was working fine, and at the same time changed the SES bulb, plugged it all back in and got code 12 when running shorted diagnostic pins.
Turned the car off, removed wire and started it and left it for 5 mins, and turned it off. That was yesterday, and then today I went for a drive down the road, only about a mile or two, and the throttle repsonse sucked ***. The car drove like a had a caravan in tow.
Is this because the ECU needs to take more readings etc? or is the problem elsewhere?
#3
Senior Member
Thread Starter
Join Date: Feb 2009
Location: Brisbane, Australia
Posts: 863
Likes: 0
Received 15 Likes
on
13 Posts
Car: 1985 Pontiac TransAM
Engine: 400SBC 24x conversion
Transmission: T700r Stage2 Shiftkitted
Axle/Gears: 2.77 9 Bolt
Re: How long for ECU to relearn?
sorry bout that.
1985 Pontiac TransAM, with 290hp 350 crate motor, 87TPI setup, 16198259(re-man 165) ECU, 19lbs injectors, MEMCAL chip, extractors into 2 cats into a 3" exhaust system, stage 2 shift kit.
Pretty sure everything plugged ok, it was just running sluggish.
1985 Pontiac TransAM, with 290hp 350 crate motor, 87TPI setup, 16198259(re-man 165) ECU, 19lbs injectors, MEMCAL chip, extractors into 2 cats into a 3" exhaust system, stage 2 shift kit.
Pretty sure everything plugged ok, it was just running sluggish.
#4
Senior Member
Thread Starter
Join Date: Feb 2009
Location: Brisbane, Australia
Posts: 863
Likes: 0
Received 15 Likes
on
13 Posts
Car: 1985 Pontiac TransAM
Engine: 400SBC 24x conversion
Transmission: T700r Stage2 Shiftkitted
Axle/Gears: 2.77 9 Bolt
Re: How long for ECU to relearn?
also if one of the pins didnt go through, wouldnt it come up as a code in the diagnostics?
#5
Senior Member
Join Date: Mar 2008
Location: nj
Posts: 428
Likes: 0
Received 0 Likes
on
0 Posts
Car: 89 iroc
Engine: l98
Transmission: tremec
#6
Senior Member
Thread Starter
Join Date: Feb 2009
Location: Brisbane, Australia
Posts: 863
Likes: 0
Received 15 Likes
on
13 Posts
Car: 1985 Pontiac TransAM
Engine: 400SBC 24x conversion
Transmission: T700r Stage2 Shiftkitted
Axle/Gears: 2.77 9 Bolt
Re: How long for ECU to relearn?
Nah it was running rough at idle, but it had a lot more power than there is now.
It was still nowhere near where it should've been for a 290hp motor but now it feels like I've got a caravan in tow.
It was still nowhere near where it should've been for a 290hp motor but now it feels like I've got a caravan in tow.
#7
Senior Member
Join Date: Mar 2008
Location: nj
Posts: 428
Likes: 0
Received 0 Likes
on
0 Posts
Car: 89 iroc
Engine: l98
Transmission: tremec
Trending Topics
#8
Supreme Member
iTrader: (2)
Join Date: Jan 2005
Location: Hurst, Texas
Posts: 10,122
Received 429 Likes
on
369 Posts
Car: 1983 G20 Chevy
Engine: 305 TPI
Transmission: 4L60
Axle/Gears: 14 bolt with 3.07 gears
Re: How long for ECU to relearn?
It honestly sounds like you are running a 305 chip with the 19# 305 injectors. If that is the case, your ECM is adding fuel and stores the fuel trims it last used. Driving it a good 30-50 miles will let it adapt and bring you back your power.
#9
Senior Member
Thread Starter
Join Date: Feb 2009
Location: Brisbane, Australia
Posts: 863
Likes: 0
Received 15 Likes
on
13 Posts
Car: 1985 Pontiac TransAM
Engine: 400SBC 24x conversion
Transmission: T700r Stage2 Shiftkitted
Axle/Gears: 2.77 9 Bolt
Re: How long for ECU to relearn?
Thanks mate. I've got it booked in for a dyno tune thursday so they should be able to get it running good I'm hoping, or at least tell me whats wrong with it.
How can i tell if the cats are clogged and how can i unclog them?
How can i tell if the cats are clogged and how can i unclog them?
Thread
Thread Starter
Forum
Replies
Last Post
MikkoV
TPI
2
09-09-2015 04:25 PM
Street Lethal
Miscellaneous Third Gen Items!
0
09-07-2015 01:09 PM