simple question,hopefully simple answer
#1
Thread Starter
Junior Member
Joined: Jun 2009
Posts: 6
Likes: 0
From: upstate ny
Car: 1989 rs
Engine: 5.7 350 4 bolt main
Transmission: 700r4
Axle/Gears: 3.83 10 bolt gm
simple question,hopefully simple answer
i have a 89 rs with a 350 4 bolt main
i know my car did not come with a 350 that year
i am not sure what vehichle the motor came out of
not sure what other info someone might need from to be able to tell me what i need
but all i am looking for his that i need sparkplug wires for my car i currently have talyor pro wires 10.4 mm wires,they are shot, would like the same ones but need them for my application, and the wires that are on there are really long , they loop almost,
just need to know what wires to buy,becuase when i got to summitracing.com they say they wont fit my application,dont want to get to short of wires thanks
any help would be appreciated
i know my car did not come with a 350 that year
i am not sure what vehichle the motor came out of
not sure what other info someone might need from to be able to tell me what i need
but all i am looking for his that i need sparkplug wires for my car i currently have talyor pro wires 10.4 mm wires,they are shot, would like the same ones but need them for my application, and the wires that are on there are really long , they loop almost,
just need to know what wires to buy,becuase when i got to summitracing.com they say they wont fit my application,dont want to get to short of wires thanks
any help would be appreciated
#2
Moderator
Joined: Jul 1999
Posts: 17,171
Likes: 138
From: 51°N 114°W, 3500'
Car: 87 IROC L98
Engine: 588 Alcohol BBC
Transmission: Powerglide
Axle/Gears: Ford 9"/31 spline spool/4.86
Re: simple question,hopefully simple answer
You'll never get too short a wire set.
This is a generic GM HEI over the valve cover, angled boot set for a SBC
http://www.summitracing.com/parts/TAY-79228/
This set is the longer wires designed to go under the headers
http://www.summitracing.com/parts/TAY-79230/
This is a generic GM HEI over the valve cover, angled boot set for a SBC
http://www.summitracing.com/parts/TAY-79228/
This set is the longer wires designed to go under the headers
http://www.summitracing.com/parts/TAY-79230/
#3
Supreme Member
Joined: Feb 2008
Posts: 1,004
Likes: 1
Car: 90 IROC
Engine: 5.7 TPI
Transmission: 4L60
Axle/Gears: 3.23
#4
Thread Starter
Junior Member
Joined: Jun 2009
Posts: 6
Likes: 0
From: upstate ny
Car: 1989 rs
Engine: 5.7 350 4 bolt main
Transmission: 700r4
Axle/Gears: 3.83 10 bolt gm
Re: simple question,hopefully simple answer
thanks for the help,the red ones are the ones i wanted to lol,,
just to make sure too long of a wire does not affect anything
just to make sure too long of a wire does not affect anything
#5
Moderator
Joined: Jul 1999
Posts: 17,171
Likes: 138
From: 51°N 114°W, 3500'
Car: 87 IROC L98
Engine: 588 Alcohol BBC
Transmission: Powerglide
Axle/Gears: Ford 9"/31 spline spool/4.86
Re: simple question,hopefully simple answer
I still run MSD 8.5 wires on my engine. By the time I'm ready to replace them, the next set I'll use are Moroso Ultra 40 and they're only 8.65mm. I doubt you have a requirement where you need 10.5mm wires.
#6
Thread Starter
Junior Member
Joined: Jun 2009
Posts: 6
Likes: 0
From: upstate ny
Car: 1989 rs
Engine: 5.7 350 4 bolt main
Transmission: 700r4
Axle/Gears: 3.83 10 bolt gm
Re: simple question,hopefully simple answer
i dont need them.... they were just on the car when i got it and i need to get new ones, which ones would you recommend, i need ones that go under the header can u point me in the right direction
Thread
Thread Starter
Forum
Replies
Last Post