ZZ4 1/4 mile times
#1
Senior Member
Thread Starter
Join Date: Jul 1999
Location: Chillicothe Ohio
Posts: 760
Likes: 0
Received 0 Likes
on
0 Posts
Car: 89 RS 355/ 89 IROC Convert
Engine: Hot Cam 355/TPI 305
Transmission: All 700r4's
ZZ4 1/4 mile times
Hey take a second and check out my sig. If I set a ZZ4 in my car with 700r4, 3:73 gears and good 60 ft. times what would think my expected times would be.
Thanks for the input
Brian Felts
------------------
1989 Camaro RS
305 .030 over Hydro Pistons
Vortech heads milled to 58cc...Performer RPM intake....LT4 cam..Crane Gold rockers...FastChip custom chip...ALum. Driveshaft...3.73 gears with Posi...underdrive pullys...Rebuilt 700R4 with Vette Servo and B&M shift Kit...MSD ignition...A/C Delete No SMOG junk....1997 SS leather interior...B&M Shifter... Ultimate TBI mods...14X3 K&N open Element Non-Drop...Hooker headers....3" exhaust with Flowmaster Cross flow 16X8 Wheels from 97 RS Spohn LCA's Spohn Panhard Bar..LETS PLAY FORD!!
www.geocities.com/feltsb
Thanks for the input
Brian Felts
------------------
1989 Camaro RS
305 .030 over Hydro Pistons
Vortech heads milled to 58cc...Performer RPM intake....LT4 cam..Crane Gold rockers...FastChip custom chip...ALum. Driveshaft...3.73 gears with Posi...underdrive pullys...Rebuilt 700R4 with Vette Servo and B&M shift Kit...MSD ignition...A/C Delete No SMOG junk....1997 SS leather interior...B&M Shifter... Ultimate TBI mods...14X3 K&N open Element Non-Drop...Hooker headers....3" exhaust with Flowmaster Cross flow 16X8 Wheels from 97 RS Spohn LCA's Spohn Panhard Bar..LETS PLAY FORD!!
www.geocities.com/feltsb
#4
What cam and heads ? A zz4 will have.... ZZ4 cam and heads! LOL
------------------
1992 Z28 5.7 TPI
ZZ4 longblock
Harland Sharp roller rockers
Accel base and SLP siamesed runners,
52MM SLP Throttle Body
Hooker Headers & Flowmaster catback
MSD6A ignition
aluminum driveshaft
World Class 5-speed
------------------
1992 Z28 5.7 TPI
ZZ4 longblock
Harland Sharp roller rockers
Accel base and SLP siamesed runners,
52MM SLP Throttle Body
Hooker Headers & Flowmaster catback
MSD6A ignition
aluminum driveshaft
World Class 5-speed
#6
Supreme Member
iTrader: (9)
what is the cam specs on a ZZ4 motor? i am assuming these times are with a stock TPI on a ZZ4 crate motor.
------------------
86 IROC
43,000 miles
305/700R4/3.23 gears
maroon, gold stickers, black interior, T-Tops.
current mods.
shift kit
headers
cat back exhaust
mods planned for this winter
cam
Adjustable fuel pressure regulator
port and polish intake and heads
lookin to run low 14s maybe squeak out a 13.9 with my stock chip
------------------
86 IROC
43,000 miles
305/700R4/3.23 gears
maroon, gold stickers, black interior, T-Tops.
current mods.
shift kit
headers
cat back exhaust
mods planned for this winter
cam
Adjustable fuel pressure regulator
port and polish intake and heads
lookin to run low 14s maybe squeak out a 13.9 with my stock chip
#7
Supreme Member
I've seen tpi setups(far from stock) run low 13s on the zz4, but I doubt a tbi would do the same. The cam is .474" intake .510" exhaust, .208° intake .221° exhaust @ .050
[This message has been edited by rezinn (edited November 25, 2001).]
[This message has been edited by rezinn (edited November 25, 2001).]
Thread
Thread Starter
Forum
Replies
Last Post
evilstuie
Tech / General Engine
22
01-09-2020 08:29 PM