Need some help with A/C bracket and Lsa Blower!
#1
Need some help with A/C bracket and Lsa Blower!
Hey guys, I posted this up on Ls1tech as well, but haven’t received an answer yet. Anyway, as some of you guys who follow me on YouTube know, I’m kind of in the middle of installing an LSA blower on my Lm7. So far I have the blower, installed a 2.4 pulley, and I’m about to install a new set of 1 7/8 longtubes. Now my next step is going to be replacing the accessory drive. I’ve been looking for a while, but I decided to go with the Lsx concepts corvette accessory drive, without Ac shown here:
https://www.lsxconcepts.com/collecti...c#.WXe9voUpCaM
Now from what I understand, corvette and Lsa spacing is the same. I’m currently running 4th gen f body accessories, with the factory Ac compressor location. I plan on pairing this Lsx Concepts set with an Lsa water pump and Lsa crank pulley, most likey gonna pin it as well. For the blower drive I’ll probably have to pick up a different sized tensioner pulley for the 2.4 pulley, but that should fit no problem.
Soooo, my question is with the A/C compressor. Will my current f body compressor and bracket line up with the Lsa crank pulley, or will I need to swap over to an Ls3 compressor and bracket? Or are the corvette and Camaro compressors the same, and can I just swap the ls1 bracket for an Ls3 bracket? Any help is greatly appreciated!
https://www.lsxconcepts.com/collecti...c#.WXe9voUpCaM
Now from what I understand, corvette and Lsa spacing is the same. I’m currently running 4th gen f body accessories, with the factory Ac compressor location. I plan on pairing this Lsx Concepts set with an Lsa water pump and Lsa crank pulley, most likey gonna pin it as well. For the blower drive I’ll probably have to pick up a different sized tensioner pulley for the 2.4 pulley, but that should fit no problem.
Soooo, my question is with the A/C compressor. Will my current f body compressor and bracket line up with the Lsa crank pulley, or will I need to swap over to an Ls3 compressor and bracket? Or are the corvette and Camaro compressors the same, and can I just swap the ls1 bracket for an Ls3 bracket? Any help is greatly appreciated!
#3
COTM Editor
iTrader: (22)
Join Date: Mar 2001
Posts: 10,075
Likes: 0
Received 1,941 Likes
on
1,325 Posts
Car: '89 Firebird
Engine: 7.0L
Transmission: T56
Re: Need some help with A/C bracket and Lsa Blower!
Not entirely sure, but I think the AC compressor is the same and the brackets just move it forward or back depending on the spacing used. You're going to need the correct bracket anyway so why not just buy the bracket and see what happens?
#6
Re: Need some help with A/C bracket and Lsa Blower!
Before I order anything, does anyone know if C5 and C6 vette accessory spacing is the same? I would need a C5 compressor to match my lines.
Last edited by LsxMatt; 04-03-2018 at 03:22 PM.
#7
Supporter/Moderator
iTrader: (7)
Join Date: Feb 2001
Location: Cincinnati, OH
Posts: 13,355
Likes: 0
Received 427 Likes
on
329 Posts
Car: '90 RS
Engine: 377 LSX
Transmission: Magnum T56
Re: Need some help with A/C bracket and Lsa Blower!
Take a look at the info on Kwik performance. They give a good description on spacing specs as well as offer tons of various brackets. You should check out their mini sanden set-up. You could run the AC in the lower position with the blower and have room for your k-member.
Also, what heads are you going to run on the 5.3 to be compatible with the LSA ports?
Also, what heads are you going to run on the 5.3 to be compatible with the LSA ports?
Trending Topics
#8
Re: Need some help with A/C bracket and Lsa Blower!
Take a look at the info on Kwik performance. They give a good description on spacing specs as well as offer tons of various brackets. You should check out their mini sanden set-up. You could run the AC in the lower position with the blower and have room for your k-member.
Also, what heads are you going to run on the 5.3 to be compatible with the LSA ports?
Also, what heads are you going to run on the 5.3 to be compatible with the LSA ports?
I ended up going with an Lsx Concepts kit with high mount alternator and A/C. Oh and for the heads Im keeping the 243's for now, I picked up adapter plates. Everything should clear the hood being I have a 2 inch cowl.
Here it is all installed for anyone who may be interested. It was designed for older muscle car retrofits, but does fit a thirdgen pretty well.
Here it is with the the new a/c hose and the 4th gen overflow tank and blower reservoir installed.
Last edited by LsxMatt; 06-20-2018 at 12:09 AM.
Thread
Thread Starter
Forum
Replies
Last Post
Chevy86 IROC-Z
Electronics
4
04-06-2019 02:07 PM