Correct ignition coil???
#1
Correct ignition coil???
I bought my 88 IROC 350 with this ignition coil. It seems to me that most of the ignition coils would have a regular plug (or 2) in it and not just 2 wires with eye terminals. Is this the correct ignition coil for my car??
#6
Re: Correct ignition coil???
No but I can make up some numbers lol.
Iirc the grey body connector is the body side harness the black is a jumper to the icm from the coil.
https://m.ebay.com/itm/GM-TPI-TBI-HE...UAAOSwPe1ULCRQ
https://m.ebay.com/itm/87-95-LT1-TPI...sAAOSw5ZBWP75G
Iirc the grey body connector is the body side harness the black is a jumper to the icm from the coil.
https://m.ebay.com/itm/GM-TPI-TBI-HE...UAAOSwPe1ULCRQ
https://m.ebay.com/itm/87-95-LT1-TPI...sAAOSw5ZBWP75G
#7
Re: Correct ignition coil???
I believe they had an adapter that plugged into the factory harness connector too. Follow the two wires back and see if they actually used it. If they did all you need is the coil.
Trending Topics
#8
Re: Correct ignition coil???
Thanks Pauly! I'll be able to do that tomorrow night or Saturday and trace it back. I tried to look at the base of the distributor to see the connectors but I wasn't able to see much of anything through the wires at the time I last tried.
#9
Re: Correct ignition coil???
Iirc the grey body connector is the body side harness the black is a jumper to the icm from the coil.
Last edited by Abubaca; 06-14-2018 at 02:57 PM.
#11
Re: Correct ignition coil???
Pauly,
good call! The original wires and connectors were still there. I was able to trace the wires back to the correct connectors. Now all I need is to figure out which MSD ignition coil to use and hopefully find an MSD ignition control module for my car. I’ve found Accel and a couple other manufacturers modules but not MSD.
good call! The original wires and connectors were still there. I was able to trace the wires back to the correct connectors. Now all I need is to figure out which MSD ignition coil to use and hopefully find an MSD ignition control module for my car. I’ve found Accel and a couple other manufacturers modules but not MSD.
#12
Supreme Member
Join Date: May 2015
Location: Florida
Posts: 1,737
Received 258 Likes
on
198 Posts
Car: 1991 Z28
Engine: 305 TPI
Transmission: 700R4
Axle/Gears: 3:42 Auburn
Re: Correct ignition coil???
Here is the MSD Blaster coil that I used.
https://www.summitracing.com/parts/m...o/submodel/z28
You are right as I could not find a MSD ICM. I used all MSD parts for the rest of the ignition(cap, rotor. wires) and I decided to buy a Jegs brand ICM.
https://www.jegs.com/i/JEGS/555/40602/10002/-1
https://www.summitracing.com/parts/m...o/submodel/z28
You are right as I could not find a MSD ICM. I used all MSD parts for the rest of the ignition(cap, rotor. wires) and I decided to buy a Jegs brand ICM.
https://www.jegs.com/i/JEGS/555/40602/10002/-1
Thread
Thread Starter
Forum
Replies
Last Post
jfox55
Tech / General Engine
8
04-08-2002 05:49 PM