Let's take the guesswork out of plastic repair!!!!!!!
#51
Senior Member
Thread Starter
That was just a link to the product page...Sorry if I wasn't clear.
The Plastic repair link is on the left of the page
The Plastic repair link is on the left of the page
#52
They list:
Super Fast AdhesiveFast Urethane Adhesive
Medium Urethane Adhesive
Semi-Rigid Epoxy Adhesive
Here: http://www.evercoat.com/productCategory.aspx?cat=6
Any specific one for what we’re talking about or all of them work well?
Super Fast AdhesiveFast Urethane Adhesive
Medium Urethane Adhesive
Semi-Rigid Epoxy Adhesive
Here: http://www.evercoat.com/productCategory.aspx?cat=6
Any specific one for what we’re talking about or all of them work well?
#53
I notice there is a Super Fast, Fast, and Medium. I dont think you want the semi-rigid from what Kevin has said here earlier in the thread. Almost sounds to me like the other three are just different work times.....but I could be wrong.
#54
Senior Member
Thread Starter
Yeah the medium is ok for what you will normally repair. They are just longer set times.
#55
Member
Join Date: Aug 2006
Location: Dallas, Georgia
Posts: 295
Likes: 0
Received 0 Likes
on
0 Posts
Car: Looking
Re: Let's take the guesswork out of plastic repair!!!!!!!
Where can this product be purchased at?
Also, I'm getting ready to paint mine, and should I have flex agent put in the paint? due to the plastice front and rear bumpers?
Also, I'm getting ready to paint mine, and should I have flex agent put in the paint? due to the plastice front and rear bumpers?
#56
Re: Let's take the guesswork out of plastic repair!!!!!!!
How about something to make a really small repair without putting myself >$50 in the hole?
Check out this thread:
https://www.thirdgen.org/forums/body...-do-i-fix.html
Check out this thread:
https://www.thirdgen.org/forums/body...-do-i-fix.html
#57
Member
Join Date: Aug 2006
Location: Dallas, Georgia
Posts: 295
Likes: 0
Received 0 Likes
on
0 Posts
Car: Looking
Re: Let's take the guesswork out of plastic repair!!!!!!!
Here's my bowtie grill. Should I use the methods described at the begining of this sticky make this repair. You can see how the finish is cracked. I was planning on just filling the cracks with two part epoxy, sanding and painting black the same day the car is painted witht the same paint. Does that sound liek the best course of action with this repair?
Last edited by rebel1222; 07-04-2007 at 07:26 AM.
#58
Senior Member
Thread Starter
Re: Let's take the guesswork out of plastic repair!!!!!!!
How about something to make a really small repair without putting myself >$50 in the hole?
Check out this thread:
https://www.thirdgen.org/forums/bo...-do-i-fix.html (How do I fix this?)
Check out this thread:
https://www.thirdgen.org/forums/bo...-do-i-fix.html (How do I fix this?)
----------
--------------------------------------------------------------------------------
Here's my bowtie grill. Should I use the methods described at the begining of this sticky make this repair. You can see how the finish is cracked. I was planning on just filling the cracks with two part epoxy, sanding and painting black the same day the car is painted witht the same paint. Does that sound liek the best course of action with this repair?
Here's my bowtie grill. Should I use the methods described at the begining of this sticky make this repair. You can see how the finish is cracked. I was planning on just filling the cracks with two part epoxy, sanding and painting black the same day the car is painted witht the same paint. Does that sound liek the best course of action with this repair?
If it's just paint damaged and split, sand it off and prime and paint.
As for the flex...you only need it on the plastic panels.
Last edited by KEVIN G.; 04-15-2007 at 07:11 PM. Reason: Automerged Doublepost
#59
Junior Member
Join Date: Mar 2007
Location: Flower Mound, TX
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
Car: 86 IROC (Red on Red)
Engine: 305 tpi
Re: Let's take the guesswork out of plastic repair!!!!!!!
I also have a question about spider web type cracks in the base plastic. I've started sanding mine down and the these cracks go through all the paint and primer and are clearly evident in the spoiler itself. Do I have to continue sanding until I get them out too? (I'm worried about keeping it even if I have to go that route) Or can I put the 3m easy sand (or equivelent) over the top to seal it and prevent it from cracking the new paint?
Last edited by spitstickler; 05-21-2007 at 02:38 PM. Reason: clarifing question.
#60
Junior Member
Join Date: Mar 2007
Location: Flower Mound, TX
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
Car: 86 IROC (Red on Red)
Engine: 305 tpi
Re: Let's take the guesswork out of plastic repair!!!!!!!
Here's a couple of pics of what I'm asking about.
And a closeup
And a closeup
#61
Junior Member
Join Date: Apr 2008
Location: Hartwood Virginia
Posts: 15
Likes: 0
Received 0 Likes
on
0 Posts
Car: 87 z/28
Engine: 305 tpi
Transmission: auto 700r4
Axle/Gears: not sure 2.73 I think
Re: Let's take the guesswork out of plastic repair!!!!!!!
I have a hole in my front bumper cover can I use this process or is just for cracks.the hole is about 1-1/2 inchs in diameter
#62
Senior Member
Join Date: Jan 2008
Location: SoCal 909
Posts: 519
Likes: 0
Received 0 Likes
on
0 Posts
Car: 91 RS vert/ 89 iroc vert
Engine: 305 TBI/305 TPI
Transmission: 700r4Xtwo
Axle/Gears: 10 bolt non-pos. B/W 9 bolt pos
Re: Let's take the guesswork out of plastic repair!!!!!!!
kevin g, the only focus on this tread has been on urethane plastic so my question is what is the proper way to fix abs plastic?
#63
Junior Member
Join Date: Dec 2008
Location: Houston, TX
Posts: 96
Likes: 0
Received 0 Likes
on
0 Posts
Car: 91 Firebird
Engine: 3.1
Re: Let's take the guesswork out of plastic repair!!!!!!!
hey kevin I noticed you haven't been on in almost 2 years now. You still there?
#64
Junior Member
iTrader: (2)
Join Date: Dec 2008
Location: Little Rock, Ar
Posts: 85
Received 0 Likes
on
0 Posts
Car: 89 Camaro IROC-Z
Engine: 350 TPI crate
Transmission: 700 R4
Axle/Gears: 9 Bolts Borg Warner 2.77
Re: Let's take the guesswork out of plastic repair!!!!!!!
How would you repair a plastic thread?
The one in my spoiler are old and fragile. I was thinking of cleaning them, then glue it with a PU glue. Screw inside it with grease/oil on the screw.
What do you think?
Edit: I am thinking that it might be ABS and not Urethane. Correct me if I am wrong.
The one in my spoiler are old and fragile. I was thinking of cleaning them, then glue it with a PU glue. Screw inside it with grease/oil on the screw.
What do you think?
Edit: I am thinking that it might be ABS and not Urethane. Correct me if I am wrong.
#65
Junior Member
Join Date: Jan 2009
Location: Richmond, VA
Posts: 12
Likes: 0
Received 0 Likes
on
0 Posts
Car: 98 Camaro 00 lifted silverado
Re: Let's take the guesswork out of plastic repair!!!!!!!
Great thread. Been around a while I think that ppl should post what they need, projects completed, What they have used.
I have a crack on an 86 Camaro ground effect. I will post pics and do reasearch to find out what works and doesnt.
I have a crack on an 86 Camaro ground effect. I will post pics and do reasearch to find out what works and doesnt.
#66
Junior Member
Join Date: Jan 2009
Location: Richmond, VA
Posts: 12
Likes: 0
Received 0 Likes
on
0 Posts
Car: 98 Camaro 00 lifted silverado
Re: Let's take the guesswork out of plastic repair!!!!!!!
#67
Re: Let's take the guesswork out of plastic repair!!!!!!!
I really like the patern in the lower left corner... I know its cracks but it would be kickass if you could simulate that effect into a paintjob.
I have been having a hell of a time trying to repair the new front lip I got... This is not as easy as you think.
I have been having a hell of a time trying to repair the new front lip I got... This is not as easy as you think.
Last edited by Slouch; 04-28-2009 at 12:38 AM.
#68
Junior Member
Join Date: Sep 2004
Posts: 19
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1989 Camaro RS
Re: Let's take the guesswork out of plastic repair!!!!!!!
Two questions, first: would it be possible to fix the two cracks? and if so what would the be the best way to go about fixing them? The cracks are in the front clip and on the passenger side ground effect. Pictures attached.
Thanks for any help.
Thanks for any help.
#69
Re: Let's take the guesswork out of plastic repair!!!!!!!
Bump, could this process be used on a corner of a front bumper? If so how would I go about getting it to stay in a good shape while the product held/cured, instead of breaking apart?
#70
Junior Member
Join Date: Jan 2009
Location: Richmond, VA
Posts: 12
Likes: 0
Received 0 Likes
on
0 Posts
Car: 98 Camaro 00 lifted silverado
Re: Let's take the guesswork out of plastic repair!!!!!!!
If you look at some of the videos within the link i posted, They use tape. Thats what i use and then sand down any imperfections. If you are able, Please post pics. Im sure someone with more experience will be able to help you.
#71
Member
Join Date: Apr 2006
Location: Bardstown, KY
Posts: 216
Likes: 0
Received 0 Likes
on
0 Posts
Car: 99 HOSS 6 Speed
Engine: LS1
Transmission: T56
Axle/Gears: 3.42
Re: Let's take the guesswork out of plastic repair!!!!!!!
#72
Junior Member
Join Date: Feb 2010
Location: fort wayne in
Posts: 6
Likes: 0
Received 0 Likes
on
0 Posts
Re: Let's take the guesswork out of plastic repair!!!!!!!
i know this thread started a whie ago, but i am trying to come up with a way to repair my wraparound spoiler(even if only for a while). would the 3m products work wellfor filling the cracks in the side corners? i have used it in repairing bumper covers with the sheet of reinforcment behind the repair and it works great but wasnt sure if it would fill very well on a spoiler. the only other problem the spoiler has is the paint is cracked on top. looks like someone didnt add flex agent when painting then some moron sat on thspoiler and the paint cracked(only cracked in the butt area on either side. going down through the thread it sounds like the 3m products should work at least for a while, just trying to buy some time before having to do the inevitible and spending a bunch of mone for a new one. who knows, maybe someone will have them cheaper.
#73
Senior Member
Join Date: Mar 2006
Location: CALI
Posts: 926
Likes: 0
Received 1 Like
on
1 Post
Car: 85' Trans Am !best car ever!
Engine: 305tpi 215hp LB9 two bolt,
Transmission: th-700r4
Axle/Gears: stock (3.27)
Re: Let's take the guesswork out of plastic repair!!!!!!!
id bondo, but a new spoiler is more favorable, a bunch of money is kinda overrated, id try the wanted section
#74
Re: Let's take the guesswork out of plastic repair!!!!!!!
hi,i have a86 camaro and a split has started on the front nose cone on left hand upper front side where top of fender meets nose cone ,next to head light and is now getting longer how can i fix it?its at top of front fender and when nose cone flexes it gets longer and paint is peeling off.please help.
#75
Junior Member
Join Date: Feb 2010
Posts: 17
Likes: 0
Received 0 Likes
on
0 Posts
Car: 87 Firebird and 93 Accord
Engine: Bird has a 355 ready to be put in
Transmission: TH-350
Axle/Gears: stock 3.43
Re: Let's take the guesswork out of plastic repair!!!!!!!
the bumper on my 87 firebird is cracked about 4 inches from the top all the way to the bottom and the crack runs along the rubber insert in the bumper. it is a verticle crack and i was wondering if it is worth it to repair it or should i just replace it
#76
Member
Join Date: Aug 2009
Location: newport news va.
Posts: 156
Likes: 0
Received 0 Likes
on
0 Posts
Car: 92 firebird gta
Engine: L98 with minor mods.
Transmission: 700r4
Axle/Gears: 3.23
Re: Let's take the guesswork out of plastic repair!!!!!!!
My spoiler on my GTA broke at the area that runs along side of the glass about six in. from the narrow end would this fix work in my case.
#77
Re: Let's take the guesswork out of plastic repair!!!!!!!
Anyone know were to get a new 92 chin spoiler. mine has a crack in the corner and im sick of it recracking everytime it get brushed on a peble. I want to see if i can get a brand new one.
________________________________________
Soundproofing
Sound Proofing
________________________________________
Soundproofing
Sound Proofing
#79
Junior Member
Join Date: Sep 2010
Location: Maryland
Posts: 17
Likes: 0
Received 0 Likes
on
0 Posts
Car: 84 Z28
Engine: 305 for now
Transmission: 350
Re: Let's take the guesswork out of plastic repair!!!!!!!
so... i started a new post looking for help with my bumper repair than i found this one. so, can and how do i fix this? (see pics)
#80
Member
iTrader: (1)
Join Date: Dec 2011
Location: under the hood of my car in Massachusetts
Posts: 179
Likes: 0
Received 0 Likes
on
0 Posts
Car: 92 rs daily driver work in progress
Engine: 3.1 , 204/214 cam
Transmission: 700 r-4, b& m megashifter
Axle/Gears: I want a posi with rear discs
Re: Let's take the guesswork out of plastic repair!!!!!!!
WTF???
Nobody mentioned duct tape and rattle cans.
Just kidding ... great info Kevin.
The PO of my car thought it would be amusing to enter driveways at the fastest speed possible without lising control. Then some lowered import steaming pile of **** decided to t-bone me so the drivers door was trashed along with the quarter and the ground efx. Gonna fix the ground efx and get the door and quarter replaced . Gonna also delete the nose emblem then get it painted.
this article will help with the ground efx.
Nobody mentioned duct tape and rattle cans.
Just kidding ... great info Kevin.
The PO of my car thought it would be amusing to enter driveways at the fastest speed possible without lising control. Then some lowered import steaming pile of **** decided to t-bone me so the drivers door was trashed along with the quarter and the ground efx. Gonna fix the ground efx and get the door and quarter replaced . Gonna also delete the nose emblem then get it painted.
this article will help with the ground efx.
#81
Originally Posted by Randy82WS7
delete,, since i am apparently invisible in here.,...
Posted from Thirdgen.org App for Android
#82
Member
Join Date: Oct 2005
Location: Michigan [Bodacious Member with the Bodacious TA'TAs (Trans Ams)]
Posts: 415
Likes: 0
Received 2 Likes
on
2 Posts
Car: 91 Formula - Authentic and REAL
Engine: 5.0 Liter
Transmission: 700R4
Re: Let's take the guesswork out of plastic repair!!!!!!!
Or you could utilize plastic welding.
#83
Re: Let's take the guesswork out of plastic repair!!!!!!!
I want to join a camaro lower half front cover to a firebird upper half cover. I have seen pics of it where you cut the front covers in half then rejoin them. My question is better to weld or will epoxy hold up?
Last edited by snakeshooter; 06-13-2015 at 07:41 AM. Reason: Clarity
#84
Junior Member
Join Date: Jun 2015
Location: san antonio tx
Posts: 1
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1984 camaro
Engine: after market 305
Transmission: 3 speed auto
Re: Let's take the guesswork out of plastic repair!!!!!!!
I'm a big believer in Bondo. I use it to fill holes, fix dents and even brackets. The front end was sticking out of my car due to a broken bracket. I just put a scoop of bondo between the front end and the fender, put pressure on it for about fifteen mins, then wham bam thank you ma'am. Good as new
#85
Member
iTrader: (1)
Join Date: Dec 2016
Location: cincinnati ohio
Posts: 252
Likes: 0
Received 5 Likes
on
4 Posts
Car: 1987 Trans am GTA
Engine: 5.7 liter
Transmission: 700r4
Axle/Gears: 3.27
Re: Let's take the guesswork out of plastic repair!!!!!!!
so, since were talking about plastic/ fiberglass repair do you think the bumper in the picture should be repaired or replaced? I was told by a paint/ body (emphasis on paint being his first choice of work) that I would be better off replacing it. as far as I can tell it doesn't have any cracks in it, just the messed up paint.
#86
Supreme Member
Re: Let's take the guesswork out of plastic repair!!!!!!!
What could you possibly have to lose by attempting the repair yourself?
You can't make it look worse unless you try to do the whole job with a chainsaw, and paint thrown from a trebouchet.
These are our hobby cars. We can go as slow as we need to to deal with the small issues. Not like the hurry-up-to-the-next-job professional shops that look at our cars and run away with their hair on fire.
If you can repaint a bicycle without it looking a complete mess, you can probably do a decent job filling the damage, and repainting the bumper on a third gen Camaro.
You can't make it look worse unless you try to do the whole job with a chainsaw, and paint thrown from a trebouchet.
These are our hobby cars. We can go as slow as we need to to deal with the small issues. Not like the hurry-up-to-the-next-job professional shops that look at our cars and run away with their hair on fire.
If you can repaint a bicycle without it looking a complete mess, you can probably do a decent job filling the damage, and repainting the bumper on a third gen Camaro.
The following users liked this post:
GreenieG (01-09-2021)
#87
Member
iTrader: (1)
Join Date: Dec 2016
Location: cincinnati ohio
Posts: 252
Likes: 0
Received 5 Likes
on
4 Posts
Car: 1987 Trans am GTA
Engine: 5.7 liter
Transmission: 700r4
Axle/Gears: 3.27
Re: Let's take the guesswork out of plastic repair!!!!!!!
Well, W.e.g, you've inspired me lol. in an attempt to keep as much of the original car in tact as possible I've started sanding down the bumper today (after finishing the removal of 20 yr old tint on the back windshield but that's another story completly) but I do have a question, should I completly strip the bumper or just sand down the really badly cracked spots and use a filler to re-level it?
#88
Re: Let's take the guesswork out of plastic repair!!!!!!!
What online website would be the best to get body party for a firebird formula, because the ground effects on front of the you're are obliterated
#90
Senior Member
Thread Starter
Re: Let's take the guesswork out of plastic repair!!!!!!!
Guys, Sorry for the long hiatus, I finally got my account back. I came to North Carolina to make a career move, and lost access to my account. I have been meaning to PM the owners of ThirdGen.org for years, but never did.
I finally contacted them for a terrible reason. Sadly I had to let my beautiful Aero go...Mice got to the engine harness and the interior, as well as behind the dash. I was heartbroken. NC is an inspection state, and the car would not pass without additional work. so I let it sit, and that's what did it in. I had that car stored in the winters in Michigan for 20 years. Each year I got it out in the spring/summer without so much as a turd...A year after bringing it down here, it developed an engine miss, and several things were not working that I know did not fail out of the blue. After some diag...all the evidence I needed was right there.
I will try to help out once in a while, as I may pop in, but right now...I'm too bummed when I look at some of your beautiful cars.
In the next few days/weeks I will be listing some of the parts I have left, in the classified section. I had re-registered a couple months ago in an alternate name, to move some of this stuff...and found a member that needed the hatch shade. We worked a deal, and I think he's very happy.
I am honest about any of the parts I have...and am happy to help another member.
Let's keep 'em alive guys....
I finally contacted them for a terrible reason. Sadly I had to let my beautiful Aero go...Mice got to the engine harness and the interior, as well as behind the dash. I was heartbroken. NC is an inspection state, and the car would not pass without additional work. so I let it sit, and that's what did it in. I had that car stored in the winters in Michigan for 20 years. Each year I got it out in the spring/summer without so much as a turd...A year after bringing it down here, it developed an engine miss, and several things were not working that I know did not fail out of the blue. After some diag...all the evidence I needed was right there.
I will try to help out once in a while, as I may pop in, but right now...I'm too bummed when I look at some of your beautiful cars.
In the next few days/weeks I will be listing some of the parts I have left, in the classified section. I had re-registered a couple months ago in an alternate name, to move some of this stuff...and found a member that needed the hatch shade. We worked a deal, and I think he's very happy.
I am honest about any of the parts I have...and am happy to help another member.
Let's keep 'em alive guys....
Thread
Thread Starter
Forum
Replies
Last Post