Zexel Torsion Posi FS
#4
Member
![](https://www.thirdgen.org/forums/images/ranks/tgo10.gif)
Join Date: Feb 2005
Location: Minnesota
Posts: 118
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Z-28
Engine: AFR ELIM 195s,280xfi,58mmLt1 Intake
Transmission: 2200stl,700r4 shift kit,vette servo
Axle/Gears: 28 spline, 3.42 gears, SLP Posi
Posi
i may be interested what would shipping be to 55014?
#6
Member
![](https://www.thirdgen.org/forums/images/ranks/tgo10.gif)
Join Date: Feb 2005
Location: Minnesota
Posts: 118
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Z-28
Engine: AFR ELIM 195s,280xfi,58mmLt1 Intake
Transmission: 2200stl,700r4 shift kit,vette servo
Axle/Gears: 28 spline, 3.42 gears, SLP Posi
posi
do i need any special tools or anythign to put this in or is it jus tlike putting in any other posi? How many miles on it? Is it noisey? can i use this in my stock 10 bolt rear? do i need special gears or will my 3.42's work?
#7
Senior Member
Thread Starter
iTrader: (1)
Join Date: Mar 2002
Location: Central Jersey
Posts: 779
Likes: 0
Received 0 Likes
on
0 Posts
well, ya just need series 3 gears. its like putting in any other posi, no its not noisey, about 30K on it, and it will work in a 10 bolt with 28 spline axles. i got one bearing off, then my tool broke, so ya just need to remove the other bearing, install new ones and go. (as you should replace carrier bearings before ya put them in on a used one.
Trending Topics
#8
Member
![](https://www.thirdgen.org/forums/images/ranks/tgo10.gif)
Join Date: Feb 2005
Location: Minnesota
Posts: 118
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Z-28
Engine: AFR ELIM 195s,280xfi,58mmLt1 Intake
Transmission: 2200stl,700r4 shift kit,vette servo
Axle/Gears: 28 spline, 3.42 gears, SLP Posi
slp zexel-torsion
i was lookin at these on summit and the only one they have on there is for a series 4 ....what is that? and is this a series 4?
#10
Member
![](https://www.thirdgen.org/forums/images/ranks/tgo10.gif)
Join Date: Feb 2005
Location: Minnesota
Posts: 118
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Z-28
Engine: AFR ELIM 195s,280xfi,58mmLt1 Intake
Transmission: 2200stl,700r4 shift kit,vette servo
Axle/Gears: 28 spline, 3.42 gears, SLP Posi
I have a thirdgen posi rear end that came factory with 3.23s and the auburn limited slip...will the fourth gen posi you have accept my 3.42's for a 7 5/8s ??
By the way thanks for being patient and answering my questions
By the way thanks for being patient and answering my questions
![thumbs up](https://www.thirdgen.org/forums/images/smilies/thumbsup.gif)
#11
Member
![](https://www.thirdgen.org/forums/images/ranks/tgo10.gif)
Join Date: Feb 2005
Location: Minnesota
Posts: 118
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Z-28
Engine: AFR ELIM 195s,280xfi,58mmLt1 Intake
Transmission: 2200stl,700r4 shift kit,vette servo
Axle/Gears: 28 spline, 3.42 gears, SLP Posi
oh duh!
i just re-read your last post and it answered my last question....so do you think i could get some pics of it? im very interested! If you need an email to send them to its Josh2319@hotmail.com
#13
Member
![](https://www.thirdgen.org/forums/images/ranks/tgo10.gif)
Join Date: Feb 2005
Location: Minnesota
Posts: 118
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Z-28
Engine: AFR ELIM 195s,280xfi,58mmLt1 Intake
Transmission: 2200stl,700r4 shift kit,vette servo
Axle/Gears: 28 spline, 3.42 gears, SLP Posi
well....am i going to get these pics??? or am i going to buy one from a differnt guy?
Thread
Thread Starter
Forum
Replies
Last Post
KO1
Engine/Drivetrain/Suspension Parts for Sale
16
10-15-2015 05:00 PM