Custom made kick panels for components
#1
Thread Starter
Supreme Member
iTrader: (9)
Joined: Sep 1999
Posts: 3,871
Likes: 24
From: Mass
Engine: 350 TPI
Transmission: A4
Axle/Gears: 3.23
Custom made kick panels for components
I am selling my custom made kick panels that were in my camaro. I made these out of OEM kick panels and used fiberglass to build out an enclosure for a pair of 6.5" components. I had Polks in and they sounded great with my amp. THese are NOT some cheap stamped plastic ones found online. Granted they are homemade but they bolt right in place of your stock kick panels. Asking $100 plus shipping for the pair. They do not come with speakers. Located in Mass.
#2
Thread Starter
Supreme Member
iTrader: (9)
Joined: Sep 1999
Posts: 3,871
Likes: 24
From: Mass
Engine: 350 TPI
Transmission: A4
Axle/Gears: 3.23
Re: Custom made kick panels for components
TTT. $85. These things are not some molded plastic crap thats out there. Very sold construction and they bolt right in place of the factory kick panel. If your interior is not black then just remove the kick panel, cut yours out and exchange the fiberglass mold and you are all done.
#3
Junior Member
Joined: Dec 2011
Posts: 14
Likes: 0
From: Carthage, Texas
Car: 1985 IROC
Engine: 305 for now
Transmission: 700-R4
Axle/Gears: 3.73 w/ auburn posi
Re: Custom made kick panels for components
Man those look good! Are those 6.5 speakers? I made a set for a truck i had they turned out good but it took too much time. How much shipped to 75633. Thanks
#6
Thread Starter
Supreme Member
iTrader: (9)
Joined: Sep 1999
Posts: 3,871
Likes: 24
From: Mass
Engine: 350 TPI
Transmission: A4
Axle/Gears: 3.23
Re: Custom made kick panels for components
$100 shipped. I will end up picking up at least a $20 tab on the shipping and loose 3% if you use paypal so I think my price is fair. These are not flimsy. Trust me when I say that they will out perform any premade pick panel you buy on the internet.
Trending Topics
#8
Member
iTrader: (7)
Joined: Nov 2010
Posts: 179
Likes: 0
From: portland, michigan
Car: 85 iroc-z28
Engine: 049 headed bbc 4?? C.I.D
Transmission: T56
Axle/Gears: 3:73 posi
Re: Custom made kick panels for components
This might sound like a dumb question but how would I wire these in? In using a 4 channel amp that I used to run with my speakers I had in my car but I switched to 4th gen dash and no speakers in the dash which sucks really bad.
Would I just wire it up the same way I used to have my dash speakers wired in? Sorry for the dumb questions but I'm not really big into audio knowledge I'm more into go fast parts.
Would I just wire it up the same way I used to have my dash speakers wired in? Sorry for the dumb questions but I'm not really big into audio knowledge I'm more into go fast parts.
#9
Thread Starter
Supreme Member
iTrader: (9)
Joined: Sep 1999
Posts: 3,871
Likes: 24
From: Mass
Engine: 350 TPI
Transmission: A4
Axle/Gears: 3.23
Re: Custom made kick panels for components
When you use a component speaker setup it will come with a crossover for each channel. The output from the head unit or the amp will go to the crossover and then you wire the components(tweeter and mid) to the crossover.
Thread
Thread Starter
Forum
Replies
Last Post