FIRST fuel injection intake GP
#101
Re: FIRST fuel injection intake GP
I have the XFI292 in my Camaro right now, I have had no problems with my springs and its been in the car for 2 years now, I have AFR 195 Comp port heads, I was thinking of leaving it in just for a dyno comparison between the FIRST and the HSR I have on the car right now, If I like it I'll keep it in for the time being, but eventualy I do plan to drop the cam down in size because I feel the XFI292 is too big for the FIRST set-up and I plan to run boost on the car so I can get my power that way with a tad more street.
If the XFI292 is close to were I like it then I might also degree it 2deg and drop the powerband down a couple RPM (Shane you might wanna look into doing that with your XFI280)
I'd still suggest the XFI268 rollor with a 355ci or when in a truck also for the 383ci, my car has the cubes and still doesnt turn on till later in the RPM range, not sure how much of that is the HSR though. At 4000RPM its like someone hit the TURBO boost lever on one of them old TYCO remot control cars
Right now with the HSR I can flash the thing to 6500rpm in a heartbeat but I get the best 1/4mile times shifting at just over 6000rpm, again I am not sure just how much of that is the HSR though
If the XFI292 is close to were I like it then I might also degree it 2deg and drop the powerband down a couple RPM (Shane you might wanna look into doing that with your XFI280)
I'd still suggest the XFI268 rollor with a 355ci or when in a truck also for the 383ci, my car has the cubes and still doesnt turn on till later in the RPM range, not sure how much of that is the HSR though. At 4000RPM its like someone hit the TURBO boost lever on one of them old TYCO remot control cars
Right now with the HSR I can flash the thing to 6500rpm in a heartbeat but I get the best 1/4mile times shifting at just over 6000rpm, again I am not sure just how much of that is the HSR though
#102
Supreme Member
Join Date: Jan 2003
Location: Arthur, Ontario, Canada
Posts: 1,323
Likes: 0
Received 0 Likes
on
0 Posts
Car: 92Z28, 99SS, 83Z28 & 86GTA
Engine: 421, LS1, 327Turbo & 383
Transmission: T-56, 4L60E, T5 & 4L60
Axle/Gears: 4:10, 3:42, 2:73 & 3:27
Re: FIRST fuel injection intake GP
#103
Senior Member
Thread Starter
iTrader: (1)
Join Date: May 2007
Location: Detroit
Posts: 847
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1989 Iroc-Z
Engine: 383 FFI
Transmission: TKO600
Axle/Gears: 3.42
Re: FIRST fuel injection intake GP
I'm thinking something in the 1800-5800 ish range for my cam. Theres some basic info here: http://firstfuelinjection.com/techsupport.htm but i think that there are a alot of things that could have been done alittle better to get more out of it. I seem to remember someone saying their FIRST was peaking at around 5800. But if you're not happy with the top end, there is always LOOOOTS of porting to be done!
Also, Ken wanted me to give you guys a big thanks, and to let you guys know that they are always there for ya guys if ya need help. He said if you have any questions to please ask and they will be as helpful as possible.
So thanks guys!!!
Also, Ken wanted me to give you guys a big thanks, and to let you guys know that they are always there for ya guys if ya need help. He said if you have any questions to please ask and they will be as helpful as possible.
So thanks guys!!!
Last edited by LMSkyliner; 01-26-2009 at 04:05 PM.
#105
Senior Member
Thread Starter
iTrader: (1)
Join Date: May 2007
Location: Detroit
Posts: 847
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1989 Iroc-Z
Engine: 383 FFI
Transmission: TKO600
Axle/Gears: 3.42
Re: FIRST fuel injection intake GP
It was supposed to end on january 15th, but there is no harm in emailing him and asking I suppose. Plus if they still have the message up maybe they are still doing it.
#106
Supreme Member
Join Date: Jan 2003
Location: Arthur, Ontario, Canada
Posts: 1,323
Likes: 0
Received 0 Likes
on
0 Posts
Car: 92Z28, 99SS, 83Z28 & 86GTA
Engine: 421, LS1, 327Turbo & 383
Transmission: T-56, 4L60E, T5 & 4L60
Axle/Gears: 4:10, 3:42, 2:73 & 3:27
Re: FIRST fuel injection intake GP
Well my FIRST just came in, it looks mean, I'll try and get some pics up asap
#107
Supreme Member
Join Date: Jan 2003
Location: Arthur, Ontario, Canada
Posts: 1,323
Likes: 0
Received 0 Likes
on
0 Posts
Car: 92Z28, 99SS, 83Z28 & 86GTA
Engine: 421, LS1, 327Turbo & 383
Transmission: T-56, 4L60E, T5 & 4L60
Axle/Gears: 4:10, 3:42, 2:73 & 3:27
Re: FIRST fuel injection intake GP
Oki, got some pics
TB looks huge, lol
Comes with all the hardware
My tech going over everything to make sure it will work
TB looks huge, lol
Comes with all the hardware
My tech going over everything to make sure it will work
#108
Supreme Member
Join Date: Jan 2003
Location: Arthur, Ontario, Canada
Posts: 1,323
Likes: 0
Received 0 Likes
on
0 Posts
Car: 92Z28, 99SS, 83Z28 & 86GTA
Engine: 421, LS1, 327Turbo & 383
Transmission: T-56, 4L60E, T5 & 4L60
Axle/Gears: 4:10, 3:42, 2:73 & 3:27
Re: FIRST fuel injection intake GP
Compairing the size diference to a stock TPI runner (beware of the possesed cat)
#109
Senior Member
Thread Starter
iTrader: (1)
Join Date: May 2007
Location: Detroit
Posts: 847
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1989 Iroc-Z
Engine: 383 FFI
Transmission: TKO600
Axle/Gears: 3.42
Re: FIRST fuel injection intake GP
wow! That thing looks mean, and that color is awsome!! Maybe I should get mine in a darker red (not a fan of the firetruck red) instead of the black I had originally planned. Also, the entire FIRST is CLEARLY much larger and better flowing than a stock TPI. I'm lovin this! I definitely needa get my order in asap.
#111
Re: FIRST fuel injection intake GP
I changed my order to black. I really like the way the edelbrock system looked in black so maybe the first will look good too. I must say that the blue looks beyond great. If I had known the paint code for my camaro I would have done the same thing. Thanks for sharing your pics!
Last edited by t/a-speedfreak; 02-04-2009 at 11:11 AM.
#113
Supreme Member
Join Date: Jan 2003
Location: Arthur, Ontario, Canada
Posts: 1,323
Likes: 0
Received 0 Likes
on
0 Posts
Car: 92Z28, 99SS, 83Z28 & 86GTA
Engine: 421, LS1, 327Turbo & 383
Transmission: T-56, 4L60E, T5 & 4L60
Axle/Gears: 4:10, 3:42, 2:73 & 3:27
#114
#115
Supreme Member
Join Date: Jan 2003
Location: Arthur, Ontario, Canada
Posts: 1,323
Likes: 0
Received 0 Likes
on
0 Posts
Car: 92Z28, 99SS, 83Z28 & 86GTA
Engine: 421, LS1, 327Turbo & 383
Transmission: T-56, 4L60E, T5 & 4L60
Axle/Gears: 4:10, 3:42, 2:73 & 3:27
Re: FIRST fuel injection intake GP
aha, sounds nice though
#117
Supreme Member
Join Date: Jan 2003
Location: Arthur, Ontario, Canada
Posts: 1,323
Likes: 0
Received 0 Likes
on
0 Posts
Car: 92Z28, 99SS, 83Z28 & 86GTA
Engine: 421, LS1, 327Turbo & 383
Transmission: T-56, 4L60E, T5 & 4L60
Axle/Gears: 4:10, 3:42, 2:73 & 3:27
Re: FIRST fuel injection intake GP
Very nice and clean looking car man
#118
Re: FIRST fuel injection intake GP
Mine came in today and the base will need some porting to match my heads and some blending in the runner to plenum areas.
Last edited by t/a-speedfreak; 02-12-2009 at 11:02 PM.
#119
Re: FIRST fuel injection intake GP
Ported the throttle body today!! Not sure what the tube in front and behind the throttlebody are for.
Last edited by t/a-speedfreak; 02-13-2009 at 09:00 PM.
#122
Re: FIRST fuel injection intake GP
My FIRST intake and AFPR arrived last night!!!
It was too cold in the garage to do much with it, but I have to say it is HUGE!!!!
The quality of the piece looks to be outstanding.
Question for those out there that have one already - what are your plans for EGR? Anyone with a corvette (I hear EGR is different on the vettes).
It was too cold in the garage to do much with it, but I have to say it is HUGE!!!!
The quality of the piece looks to be outstanding.
Question for those out there that have one already - what are your plans for EGR? Anyone with a corvette (I hear EGR is different on the vettes).
#123
Member
iTrader: (1)
Join Date: Jul 2006
Location: Stoughton, MA
Posts: 129
Likes: 0
Received 0 Likes
on
0 Posts
Engine: 5.7 vortec crate w/TPI
Transmission: 2004r
Axle/Gears: 3.42
Re: FIRST fuel injection intake GP
My FIRST intake and AFPR arrived last night!!!
It was too cold in the garage to do much with it, but I have to say it is HUGE!!!!
The quality of the piece looks to be outstanding.
Question for those out there that have one already - what are your plans for EGR? Anyone with a corvette (I hear EGR is different on the vettes).
It was too cold in the garage to do much with it, but I have to say it is HUGE!!!!
The quality of the piece looks to be outstanding.
Question for those out there that have one already - what are your plans for EGR? Anyone with a corvette (I hear EGR is different on the vettes).
What are you running for an AFPR?
#126
Junior Member
Join Date: Feb 2007
Location: Idaho
Posts: 2
Likes: 0
Received 0 Likes
on
0 Posts
Car: All go and no show!!!!
Engine: 383 AFR 195s First Manifold
Transmission: 700r4
Axle/Gears: corperate 9 1/2 14 bolt 4:11
Re: FIRST fuel injection intake GP
Any one install theirs yet? Just curious if you like the performance from it. The pics posted look awesome. Makes me wish I would have ordered mine painted. Hawk 92 z thanks for the advise on advancing the cam, I am having a custom torque converter made for the truck, to make up a little for cam. Still crossing my fingers that I have thought this all out well enough. Planning a new engine is a little stressful to me. (want everything right and costs a lot)
#128
Member
iTrader: (1)
Join Date: Jul 2006
Location: Stoughton, MA
Posts: 129
Likes: 0
Received 0 Likes
on
0 Posts
Engine: 5.7 vortec crate w/TPI
Transmission: 2004r
Axle/Gears: 3.42
Re: FIRST fuel injection intake GP
Anyone have theirs installed yet?
If so, would you mind taking a few pictures of your throttle body linkage and explaining how you hooked it up?
My TB didn't come with any studs to hook the TV and throttle cables to, and I'd like to see how other did this.
If so, would you mind taking a few pictures of your throttle body linkage and explaining how you hooked it up?
My TB didn't come with any studs to hook the TV and throttle cables to, and I'd like to see how other did this.
#131
Junior Member
Join Date: Nov 2008
Location: L.A
Posts: 8
Likes: 0
Received 0 Likes
on
0 Posts
Car: 85 Z28
Engine: 305 TPI
Transmission: 700R-4
Axle/Gears: 3.23
Re: FIRST fuel injection intake GP
Hey I was wondering where were you guys plan on mounting the afpr? I also got the aeromotive one that ken recomended, I was just curious as to where people were mounting there's.
#137
Member
iTrader: (1)
Join Date: Jul 2006
Location: Stoughton, MA
Posts: 129
Likes: 0
Received 0 Likes
on
0 Posts
Engine: 5.7 vortec crate w/TPI
Transmission: 2004r
Axle/Gears: 3.42
Re: FIRST fuel injection intake GP
I replied in my other thread about this. Still trying to figure it out myself.
By the way, you stole my color scheme!
Here's my engine bay currently:
Still working on finishing up the fuel lines and a couple of other small things.
#138
Junior Member
Join Date: Nov 2008
Location: L.A
Posts: 8
Likes: 0
Received 0 Likes
on
0 Posts
Car: 85 Z28
Engine: 305 TPI
Transmission: 700R-4
Axle/Gears: 3.23
Re: FIRST fuel injection intake GP
It's taken a while, but here a few pictures of my progress. Not done yet, still have to tighten the runners, install the plenum etc...
Thread
Thread Starter
Forum
Replies
Last Post
9192camaro
Engine/Drivetrain/Suspension Parts for Sale
16
02-03-2019 12:21 AM
Fast355
DFI and ECM
14
12-02-2016 06:33 PM