zya5point0

iTrader: (4)

After almost 10 years, I finally have the means to build my car the way i want it(ls1/t56), if i can sell my curent setup...that being said, here's what i got...i did this motor about 8 years ago, but it i've only put maybe 25k on car since. started with zz4, installed HOT cam, new valvesprings(not sure of specs), comp cams pro magnum roller rockers. also had basic "street" port work done by a local shop($600 back then). motor easily revs over 6500rpm and still pulling. problem is i've never gotten the trans to work properly with that motor. it does run and drive and will leave in car untill sold so somebody can come and drive it. anyway, asking $1800obo for motor with trans. if i sell the motor, i won't be needing the SLP headers i got. never used 1 3/4in primarys for 89-92 dual cat set-up with air tubes, $450 obo. also have install kit, but i think a couple pices may have got lost. will include with headers tho. also have layin around...2 wheel spacers to put 4th gen wheels on 3rd gen car(installed rear from a 95t/a so no longer need for back), $50 obo shipped. TPI wiring harness, complete and uncut from 88 5.7 iroc(sorry, no ecm), $75 obo shipped. also, if anybody wants or knows some one wants it i got a complete wiring harness with ecm from a 94 lt1 trans am. $50 shipped? i am located in south east pa(near philadelphia). any questions feel free to call me, 267-377-5923. thanx, brent

zya5point0

iTrader: (4)

If i'm askin too much for the motor and trans, don't be afraid to tell me. just tryin to get whatever i can out of it to put towards an ls1. will take any reasonable offer. the other stuff is gonna get trashed if nobody wants anything. i've had the stuff layin around too long. just fyi

FlippindaBird

iTrader: (10)

40 for the spacers shipped to 18428?

SiCkRs

iTrader: (6)

Do you got any pics of the headers

racing geek

iTrader: (5)

pm sent

CamKid1992

looking for the motor is it complete. could you send me specs and milage

zya5point0

iTrader: (4)

40 for the spacers, yea, I'm good with that. Can't get pics to post here, but give me an email address and I can send some. I don't really wanna sel my headers yet tho till I sell my motor.

SiCkRs

iTrader: (6)

castrorodolfo28@yahoo.com

zya5point0

iTrader: (4)

ok guys, i've gotten lots of interest in just the motor. a couple things...if there is anyone who may be interested in just the transmission please let me know. if i separate them i'd like to have a buyer lined up for trans so it can be road tested. how about 200 obo for just trans and converter? i don't know the exact part number for converter, but it is a vette converter i got new from gm. i had read that a vette converter had a higher stall speed and at the time i didn't have the money for an aftermarket one so thats what i put in. as far as selling motor by itself, i want to be fair and reasonable to whoever would get it as well as myself... how about starting with 1500 obo? i've given all the specs on it, but i want to make sure every one knows what the're buyin. who ever gets it i would plan on freshening it up. that was my original plan. it does run fine with good oil pressure, but because it sat more than it was driven it does leak some. any other questions, please e-mail me at cya5point0@aol.com. its easier for me to check e-mail than pm's on a blackberry(especially while driving).

mister_hudson

iTrader: (3)

Did you sell the spacers? If not I am interested!

3rd gen Will

iTrader: (8)

1500 for a ZZ4 w/ a hotcam, damn I wish you were closer!!

jason8289

Is the engine still for sale?

ogg__666

hey i need a Throttle cable,Kickdown cable,fuel lines and fuel pump how much for them and how much fro shiping to V0N 2P0 ? and the brackit on the side of the tpi