[NC] ***SOLD*** SBC Single Turbo Headers w/Crossover Pipe
08-07-2009 | 10:36 AM
#1
Thread Starter
Junior Member
Joined: May 2005
Posts: 28
Likes: 0
From: Fayetteville, NC
Car: 1991 1LE CAMARO
Engine: 383 TPI W/NOS Fogger Kit
Transmission: WC T-5
Axle/Gears: 3.42
***SOLD*** SBC Single Turbo Headers w/Crossover Pipe
SOLD!!!!!!
Stainless Single Turbo SBC Headers with the Crossover Pipe..Bought a year or so again with a project in mind...You know how that goes...
Installed on engine stand only to check fit..Went on great, no issues, cleared oil pan and all.....
Complete as pictured, will include hardware for install....
$250.00, you pay shipping.....
Stainless Single Turbo SBC Headers with the Crossover Pipe..Bought a year or so again with a project in mind...You know how that goes...
Installed on engine stand only to check fit..Went on great, no issues, cleared oil pan and all.....
Complete as pictured, will include hardware for install....
$250.00, you pay shipping.....
Last edited by 19911LECAMARO; 08-09-2009 at 08:24 AM. Reason: sold
08-07-2009 | 03:44 PM
#4
Joined: Jul 2002
Posts: 1,267
Likes: 1
From: Usa
Car: 85 IROC-Z
Engine: magflatoVE
Transmission: T56
Axle/Gears: 9" 411
08-07-2009 | 04:01 PM
#5
Supreme Member
iTrader: (33)
Joined: Jul 2000
Posts: 5,945
Likes: 1
From: Boosted Land
Car: 92 Z28
Engine: Boosted LSX
Re: SBC Single Turbo Headers w/Crossover Pipe
good for the price your payin.
You can tell they dont "purge" the inside while welding. Overall Id say make a brace for the turbo so all the weights not on the header & put a v band clamp on the slip fit crossover and your good to go. Id ceramic coat the inside.
Yes its a stainless setup but you can tell its not the best. Its a 304 http://www.azom.com/Details.asp?ArticleID=965
Ther are seam welded tubes. not manderal bends,etc.
ANyways sorry to Hijack the thread.
Would I use the setup for the price YES. deff. a good price for a entry leval stainless turbo setup. Just brace the turbo and have fun.
You can tell they dont "purge" the inside while welding. Overall Id say make a brace for the turbo so all the weights not on the header & put a v band clamp on the slip fit crossover and your good to go. Id ceramic coat the inside.
Yes its a stainless setup but you can tell its not the best. Its a 304 http://www.azom.com/Details.asp?ArticleID=965
Ther are seam welded tubes. not manderal bends,etc.
ANyways sorry to Hijack the thread.
Would I use the setup for the price YES. deff. a good price for a entry leval stainless turbo setup. Just brace the turbo and have fun.
08-07-2009 | 05:10 PM
#7
Thread Starter
Junior Member
Joined: May 2005
Posts: 28
Likes: 0
From: Fayetteville, NC
Car: 1991 1LE CAMARO
Engine: 383 TPI W/NOS Fogger Kit
Transmission: WC T-5
Axle/Gears: 3.42
Re: SBC Single Turbo Headers w/Crossover Pipe
No problem 400Z28 Racer....As stated by TPI383, it's not bad for the price...
Trending Topics
08-07-2009 | 07:27 PM
#8
Supreme Member
iTrader: (33)
Joined: Jul 2000
Posts: 5,945
Likes: 1
From: Boosted Land
Car: 92 Z28
Engine: Boosted LSX
Re: SBC Single Turbo Headers w/Crossover Pipe
No problem. Figure the info could also help the sale. Id run em if I wasnt playin around with this supercharger now.
09-11-2009 | 10:59 PM
#11
Member
Joined: Nov 2007
Posts: 115
Likes: 0
From: parma,OH
Car: 91 camaro RS
Engine: 350, forged 355 in the works
Transmission: 4 speed goin to th400
Axle/Gears: stock 9bolt, 3.27
Re: SBC Single Turbo Headers w/Crossover Pipe
anybody got a set for sale or got a link where i can buy a single turbo set up
Thread
Thread Starter
Forum
Replies
Last Post
Street Lethal
Power Adders
634
04-30-2019 12:14 PM
LT1Formula
Engine/Drivetrain/Suspension Parts for Sale
20
11-14-2015 12:02 AM
hectre13
Engine/Drivetrain/Suspension Parts for Sale
6
09-08-2015 03:38 PM
