BBS Designs Manifold + Other Stuff
#1
Member
Thread Starter
Join Date: Oct 2001
Location: Anderson, IN
Posts: 414
Likes: 0
Received 0 Likes
on
0 Posts
Car: 86 Cutlass
Engine: 350
Transmission: 200-4R
BBS Designs Manifold + Other Stuff
BBS Designs Single Turbo race manifold - Purchased this earlier this year when he was making them again. Never been installed or ran, only taken out of the box to look at. $500
Ebay BBS Knock Off - This is the ebay setup that mimics the BBS designs header. I picked this up basically for the drivers side manifold and the crossover. Comes with the drivers side manifold, crossover, passenger side manifold, and gaskets. Also never used, I'm going in a different direction. Don't remember how much they're going for, so $250?
2 .60/.63 Turbocoupe T3s. One is still intact, the center housing seems to be good, with minimal shaft play. The other is torn apart, the bolts snapped off in the exhaust housing and will need to be drilled out and probably re-tapped. Have a new center housing for this one. Also have two C4 Vette stainless manifolds. Was going to use these for a twin turbo setup, but had clearance issues (G-body, from pictures I've seen they fit better in an F-body). Make me an offer.
87 TPI base, runners, plenum and fuel rails. The base was port matched to a Fel-Pro 1205 gasket and siamesed 2.5". Plenum was ported, stock runners. Make me an offer.
You can respond here or email me at DJackson1357@yahoo.com
Ebay BBS Knock Off - This is the ebay setup that mimics the BBS designs header. I picked this up basically for the drivers side manifold and the crossover. Comes with the drivers side manifold, crossover, passenger side manifold, and gaskets. Also never used, I'm going in a different direction. Don't remember how much they're going for, so $250?
2 .60/.63 Turbocoupe T3s. One is still intact, the center housing seems to be good, with minimal shaft play. The other is torn apart, the bolts snapped off in the exhaust housing and will need to be drilled out and probably re-tapped. Have a new center housing for this one. Also have two C4 Vette stainless manifolds. Was going to use these for a twin turbo setup, but had clearance issues (G-body, from pictures I've seen they fit better in an F-body). Make me an offer.
87 TPI base, runners, plenum and fuel rails. The base was port matched to a Fel-Pro 1205 gasket and siamesed 2.5". Plenum was ported, stock runners. Make me an offer.
You can respond here or email me at DJackson1357@yahoo.com
#2
TGO Supporter
iTrader: (5)
Join Date: Feb 2000
Location: St. Augustine, FL
Posts: 1,852
Likes: 0
Received 12 Likes
on
11 Posts
Car: 89 GTA
Engine: 383
Transmission: 4L80E
Axle/Gears: 12 bolt-3.73
Re: BBS Designs Manifold + Other Stuff
How much for just the tpi base? Do you have pics of the ebay turbo headers, I don't think I've ever seen them?
#3
Supreme Member
iTrader: (1)
Join Date: Dec 2003
Location: Queens, NY
Posts: 1,342
Likes: 0
Received 0 Likes
on
0 Posts
Car: 87 IROC Z28
Engine: Custom Forged 355
Transmission: 700R4
Axle/Gears: 9" 4:11's Detroit Locker
Re: BBS Designs Manifold + Other Stuff
post some pics...i might take most of this stuff of your hands....pm me
#4
Member
Thread Starter
Join Date: Oct 2001
Location: Anderson, IN
Posts: 414
Likes: 0
Received 0 Likes
on
0 Posts
Car: 86 Cutlass
Engine: 350
Transmission: 200-4R
Re: BBS Designs Manifold + Other Stuff
I'm not really sure how much the TPI stuff goes for now days, $50? The ebay headers look pretty much exactly like the old BBS setup. I'll get some pictures of this stuff this weekend and get it sent out to you guys.
#5
Member
Thread Starter
Join Date: Oct 2001
Location: Anderson, IN
Posts: 414
Likes: 0
Received 0 Likes
on
0 Posts
Car: 86 Cutlass
Engine: 350
Transmission: 200-4R
Re: BBS Designs Manifold + Other Stuff
#6
Re: BBS Designs Manifold + Other Stuff
Hi, just a long shot. . . Just wondering if you already sold your turbo exhaust stuff. The BBS turbo header and the E-Bay single turbo kit? If you still have them, please reply to me at parrot-guy@hotmail.com Thanks. Phillip.
#7
Member
iTrader: (2)
Join Date: Aug 2002
Location: Calvert Co. Maryland
Posts: 368
Likes: 0
Received 0 Likes
on
0 Posts
Car: 91z28
Engine: 5.7 l98
Transmission: AT :(
Re: BBS Designs Manifold + Other Stuff
I to am interested in a headder.. so you got the bbs, then the ebay to make a tt kit?
they look like they are the passenger side header?
do you have the wastegate or bov ?
-T
they look like they are the passenger side header?
do you have the wastegate or bov ?
-T
Thread
Thread Starter
Forum
Replies
Last Post
86CamaroDan
Engine/Drivetrain/Suspension Parts for Sale
2
09-29-2015 10:08 PM
dimented24x7
Tech / General Engine
4
09-06-2015 03:51 PM