Belltech p/n 2200 Dropped Spindles
#1
Member
Thread Starter
iTrader: (6)
Join Date: Jul 2004
Location: RogueValley, Oregon
Posts: 405
Likes: 0
Received 0 Likes
on
0 Posts
Car: 84Z & Porsche
Engine: 427sbc - 471 - 850 Demon Claw
Transmission: Bowtie stage II TH700R4 - 10" 3000
Axle/Gears: 9 Bolt w/ 3:45's
Belltech p/n 2200 Dropped Spindles
Belltech p/n 2200 Dropped Spindles - Used 200 miles only - selling these for a friend who took them back off, did not like his car lowered. Then they sat in his garage for years (still in perfect shape) - 1.5inch drop progressive rear springs come with them (New) - $300 + shipping.
28mm Rear Sway Bar for Third Gen F body‘s, adjustable, used - $75.00+shipping
Ed (AKA:Cocacolakidd)
nushi@charter.net
541-776-9919
Rogue Valley, Oregon
28mm Rear Sway Bar for Third Gen F body‘s, adjustable, used - $75.00+shipping
Ed (AKA:Cocacolakidd)
nushi@charter.net
541-776-9919
Rogue Valley, Oregon
#2
Member
Thread Starter
iTrader: (6)
Join Date: Jul 2004
Location: RogueValley, Oregon
Posts: 405
Likes: 0
Received 0 Likes
on
0 Posts
Car: 84Z & Porsche
Engine: 427sbc - 471 - 850 Demon Claw
Transmission: Bowtie stage II TH700R4 - 10" 3000
Axle/Gears: 9 Bolt w/ 3:45's
Re: Belltech p/n 2200 Dropped Spindles
Bump - Bumpety bump.
I would think that someone would want to lower their car the right way.
These are probably the rarest part one might look for for a Third Gen F Body.
These may be the last set one ever hears of - Very Rare - Belltech stopped producing p/n 2200 Dropped Spindles for our Third Gens. years ago... Last call
I would think that someone would want to lower their car the right way.
These are probably the rarest part one might look for for a Third Gen F Body.
These may be the last set one ever hears of - Very Rare - Belltech stopped producing p/n 2200 Dropped Spindles for our Third Gens. years ago... Last call
#5
Member
Thread Starter
iTrader: (6)
Join Date: Jul 2004
Location: RogueValley, Oregon
Posts: 405
Likes: 0
Received 0 Likes
on
0 Posts
Car: 84Z & Porsche
Engine: 427sbc - 471 - 850 Demon Claw
Transmission: Bowtie stage II TH700R4 - 10" 3000
Axle/Gears: 9 Bolt w/ 3:45's
Re: Belltech p/n 2200 Dropped Spindles
Hello,
I do not have pics of the Dropped Spindles installed as it has been a couple of years since they were installed - I have regular pics though. Need some please send email and I will attach pics - That goes for the sway bar also.
On the 28mm sway bar it is adjustable because it has seperate holes on the terminal ends to set them soft or hard according to which hole they are mounted with. On the ends of most all Third Gen Sway bars there is only one hole, and therefore not adjustable.
Ed.
I do not have pics of the Dropped Spindles installed as it has been a couple of years since they were installed - I have regular pics though. Need some please send email and I will attach pics - That goes for the sway bar also.
On the 28mm sway bar it is adjustable because it has seperate holes on the terminal ends to set them soft or hard according to which hole they are mounted with. On the ends of most all Third Gen Sway bars there is only one hole, and therefore not adjustable.
Ed.
#6
Member
Thread Starter
iTrader: (6)
Join Date: Jul 2004
Location: RogueValley, Oregon
Posts: 405
Likes: 0
Received 0 Likes
on
0 Posts
Car: 84Z & Porsche
Engine: 427sbc - 471 - 850 Demon Claw
Transmission: Bowtie stage II TH700R4 - 10" 3000
Axle/Gears: 9 Bolt w/ 3:45's
Re: Belltech p/n 2200 Dropped Spindles
Hello,
Or do you mean a picture of a car lowered 2" by Dropped Spindles. I could take some pics of my Z28 that is lowered 2" to give you an idea of what a Camaro looks like with Dropped Spindles.
They really help with the steering geometry as it is the same with dropped spindles. With dropped springs the steering geometry is not the same, springs change that - also springs put quite a bind on the ball joints, and other steering parts...shocks/struts, etc.
The only problem I have found with lowering is minor tire rub when extreem lock to lock turning in a parking lot. There again I have 4th Gen Rims 2" out on spacers.
Send email addy for pics
Thanks for the replys, Ed.
Or do you mean a picture of a car lowered 2" by Dropped Spindles. I could take some pics of my Z28 that is lowered 2" to give you an idea of what a Camaro looks like with Dropped Spindles.
They really help with the steering geometry as it is the same with dropped spindles. With dropped springs the steering geometry is not the same, springs change that - also springs put quite a bind on the ball joints, and other steering parts...shocks/struts, etc.
The only problem I have found with lowering is minor tire rub when extreem lock to lock turning in a parking lot. There again I have 4th Gen Rims 2" out on spacers.
Send email addy for pics
Thanks for the replys, Ed.
Trending Topics
#8
Member
Thread Starter
iTrader: (6)
Join Date: Jul 2004
Location: RogueValley, Oregon
Posts: 405
Likes: 0
Received 0 Likes
on
0 Posts
Car: 84Z & Porsche
Engine: 427sbc - 471 - 850 Demon Claw
Transmission: Bowtie stage II TH700R4 - 10" 3000
Axle/Gears: 9 Bolt w/ 3:45's
Re: Belltech p/n 2200 Dropped Spindles
Purplehaze you could always put Dropped Spindles and Lowering Springs on so you could push around beer cans with the front bumper - Or scrape up loose change with the Air Dam - Ha, Ha.
#9
#10
Member
Thread Starter
iTrader: (6)
Join Date: Jul 2004
Location: RogueValley, Oregon
Posts: 405
Likes: 0
Received 0 Likes
on
0 Posts
Car: 84Z & Porsche
Engine: 427sbc - 471 - 850 Demon Claw
Transmission: Bowtie stage II TH700R4 - 10" 3000
Axle/Gears: 9 Bolt w/ 3:45's
Re: Belltech p/n 2200 Dropped Spindles
Purplehaze you could always put Dropped Spindles and Lowering Springs on so you could push around beer cans with the front bumper - Or scrape up loose change with the Air Dam - Ha, Ha.
I thought for shure I would give the TGO guys first crack, but may have to list them you know where next. Yes this is a surprise that they're not gone already, oh well.
I thought for shure I would give the TGO guys first crack, but may have to list them you know where next. Yes this is a surprise that they're not gone already, oh well.
#11
Member
Thread Starter
iTrader: (6)
Join Date: Jul 2004
Location: RogueValley, Oregon
Posts: 405
Likes: 0
Received 0 Likes
on
0 Posts
Car: 84Z & Porsche
Engine: 427sbc - 471 - 850 Demon Claw
Transmission: Bowtie stage II TH700R4 - 10" 3000
Axle/Gears: 9 Bolt w/ 3:45's
Re: Belltech p/n 2200 Dropped Spindles
PM back...
#12
Senior Member
iTrader: (1)
Join Date: Nov 2006
Location: Jackson, TN
Posts: 485
Likes: 0
Received 0 Likes
on
0 Posts
Car: 88 GTA
Engine: L98
Transmission: 700r4
Axle/Gears: 3.27 9bolt
Re: Belltech p/n 2200 Dropped Spindles
my email is Ls7colorado@yahoo.com
I have a trans am and really want the front lowered around 1.5" I dont know if 2" will be to low or not. Id like to go about 1" in the rear but I dont know if 1.5" will be to much. ect...
thanks
I have a trans am and really want the front lowered around 1.5" I dont know if 2" will be to low or not. Id like to go about 1" in the rear but I dont know if 1.5" will be to much. ect...
thanks
#13
Member
Join Date: Mar 2005
Location: Mass
Posts: 134
Likes: 0
Received 0 Likes
on
0 Posts
Car: 91 Z
Engine: Somethin Nice!!
Transmission: T56
Re: Belltech p/n 2200 Dropped Spindles
very interested sent a PM...also will these work with aftermarket brake setups? possibly 1LE or even baer? or does baer still send there own spindles?
#15
Member
Thread Starter
iTrader: (6)
Join Date: Jul 2004
Location: RogueValley, Oregon
Posts: 405
Likes: 0
Received 0 Likes
on
0 Posts
Car: 84Z & Porsche
Engine: 427sbc - 471 - 850 Demon Claw
Transmission: Bowtie stage II TH700R4 - 10" 3000
Axle/Gears: 9 Bolt w/ 3:45's
Re: Belltech p/n 2200 Dropped Spindles
Still for sale -
#16
Member
iTrader: (1)
Join Date: Dec 2006
Location: New Jersey
Posts: 143
Likes: 0
Received 0 Likes
on
0 Posts
Car: 88 Camaro Evoluzione Rebody
Engine: 350
Transmission: wc t5 swap completed!
Axle/Gears: 3.73 10 bolt
Re: Belltech p/n 2200 Dropped Spindles
I'll take the spindles. What address to send paypal to?
I'm in zip code 07746.
I'm in zip code 07746.
#17
Member
iTrader: (5)
Join Date: Jan 2004
Location: WPB, FL
Posts: 431
Likes: 0
Received 5 Likes
on
5 Posts
Car: '89 Trans Am GTA
Engine: TPI350
Transmission: 700r4
Axle/Gears: BW 3.27s
Re: Belltech p/n 2200 Dropped Spindles
I can't believe I missed these on here... put me in line if the other guy backs out. Thanks
#18
Member
Thread Starter
iTrader: (6)
Join Date: Jul 2004
Location: RogueValley, Oregon
Posts: 405
Likes: 0
Received 0 Likes
on
0 Posts
Car: 84Z & Porsche
Engine: 427sbc - 471 - 850 Demon Claw
Transmission: Bowtie stage II TH700R4 - 10" 3000
Axle/Gears: 9 Bolt w/ 3:45's
Re: Belltech p/n 2200 Dropped Spindles
Spindles Sold