wiring harness locations.....
#1
wiring harness locations.....
I am reinstalling the wiring harness and other wiring on my 92Z after 4 years of sitting around and I forgot some stuff.
The harness runs from the passenger side accross the engine to the drivers side and then down the fenders to the front of the bay. Here are the questions I have so far:
1. there are two sets of short wires behind the engine coming from the wiring loom that look like ground wires, are they supposed to be bolted to the heads or to the engine block and where exactly?
2. the wiring harness runs either under or over the air conditioning housing and the break booster, which is it?
Does anyone have any good photos or diagrams of 92Z engine wiring paths and connections? This would be great.
Thanks,
Jim
The harness runs from the passenger side accross the engine to the drivers side and then down the fenders to the front of the bay. Here are the questions I have so far:
1. there are two sets of short wires behind the engine coming from the wiring loom that look like ground wires, are they supposed to be bolted to the heads or to the engine block and where exactly?
2. the wiring harness runs either under or over the air conditioning housing and the break booster, which is it?
Does anyone have any good photos or diagrams of 92Z engine wiring paths and connections? This would be great.
Thanks,
Jim
#2
Supreme Member
iTrader: (4)
Join Date: Mar 2009
Location: Pepperell, MA
Posts: 3,079
Likes: 0
Received 3 Likes
on
3 Posts
Car: 1987 Trans Am
Engine: LQ9/L92
Transmission: 4L60E
Re: wiring harness locations.....
1. should be bolted to the back side of the passenger side head
2. not 100% sure since my harness has been out for a few weeks now, but believe it goes over the heater box and under the master cylinder.
2. not 100% sure since my harness has been out for a few weeks now, but believe it goes over the heater box and under the master cylinder.
#4
Supreme Member
iTrader: (7)
Join Date: Mar 2000
Location: Orange, CA
Posts: 5,677
Likes: 0
Received 112 Likes
on
67 Posts
Car: '90 Trans Am-12.45@110.71
Engine: 355 w/AFR 195's Elem. 400/430 HP/TQ
Transmission: Tremec T-56
Axle/Gears: 12 Bolt 3.73
Re: wiring harness locations.....
I am reinstalling the wiring harness and other wiring on my 92Z after 4 years of sitting around and I forgot some stuff.
The harness runs from the passenger side accross the engine to the drivers side and then down the fenders to the front of the bay. Here are the questions I have so far:
1. there are two sets of short wires behind the engine coming from the wiring loom that look like ground wires, are they supposed to be bolted to the heads or to the engine block and where exactly?
2. the wiring harness runs either under or over the air conditioning housing and the break booster, which is it?
Does anyone have any good photos or diagrams of 92Z engine wiring paths and connections? This would be great.
Thanks,
Jim
The harness runs from the passenger side accross the engine to the drivers side and then down the fenders to the front of the bay. Here are the questions I have so far:
1. there are two sets of short wires behind the engine coming from the wiring loom that look like ground wires, are they supposed to be bolted to the heads or to the engine block and where exactly?
2. the wiring harness runs either under or over the air conditioning housing and the break booster, which is it?
Does anyone have any good photos or diagrams of 92Z engine wiring paths and connections? This would be great.
Thanks,
Jim
Come by and I will give you a refresher course LOL
Don>>>
Thread
Thread Starter
Forum
Replies
Last Post