Anyone using the Xtronics ROMulator?
#1
Anyone using the Xtronics ROMulator?
Just bought one, the ROMulator programs fine but my car doesn't like it - it runs in Limp home only. You just replace the ECU chip with the ROMulator cable, right?
Thanks, -Bill
Thanks, -Bill
#2
Supreme Member
Join Date: Jun 2002
Location: great lakes
Posts: 1,787
Likes: 0
Received 0 Likes
on
0 Posts
call george there has been an issue with the header ribbon cable. also make sure the the red stripe represents pin 1. here is goerges number.or call who ever. lol. just call xtronics.
1-785-841-3089
see you later.
1-785-841-3089
see you later.
#3
Originally posted by funstick
call george there has been an issue with the header ribbon cable. also make sure the the red stripe represents pin 1. here is goerges number.or call who ever. lol. just call xtronics.
1-785-841-3089
see you later.
call george there has been an issue with the header ribbon cable. also make sure the the red stripe represents pin 1. here is goerges number.or call who ever. lol. just call xtronics.
1-785-841-3089
see you later.
#4
Member
iTrader: (3)
Join Date: Jul 1999
Location: Latham NY USA
Posts: 300
Likes: 0
Received 0 Likes
on
0 Posts
Car: 91 Formula
Engine: 350
Transmission: T-56
Axle/Gears: 10 Bolt 3.23
Let us know how well it works and whether or not you work out all the bugs. Haven't seen anyone comment on how well or if it actually works.
#5
Supreme Member
Join Date: Jun 2002
Location: great lakes
Posts: 1,787
Likes: 0
Received 0 Likes
on
0 Posts
i have one it works fine on c3 ecms. im gonna be using it tommorow with a p4 1227749 so then ill have a definate yes or no on that one for sure. ive used it on hondas with no trouble and they use a 27c256 so if that any indicator then everything is honkey dorey.
#7
Supreme Member
Join Date: Jun 2000
Location: the garage
Posts: 1,612
Likes: 0
Received 0 Likes
on
0 Posts
Car: 84 SVO
Engine: Volvo headed 2.3T
Transmission: WCT5
Axle/Gears: 8.8" 3.73
Tried running one on my 749 bench... 2 different romulators, 2 different laptops... no go with either in any combo. Bench works just fine running my flash. good luck. Bob
Trending Topics
#8
Supreme Member
Join Date: Jun 2002
Location: great lakes
Posts: 1,787
Likes: 0
Received 0 Likes
on
0 Posts
must need to have a resitor value changed ill check into that. this is with the new romulator correct. if its not emulating then you need to pitch a holy **** fit. i know i will if mine doesnt. i also think it might have to do with the mecal adapter if it isnt working. with the c3 ecms if its not super tight with the pins then it wont work at all. maybe ill rig up a 28 pin header to slip directly to the ecm this might be the problem to much signal latency. im headed out to try my romutlator now did you try to emulate with a c3 ecm like a 747 ? also were you geting a RED led with ECM power on with the romulator plugged into the ecm but disconnected from the laptop ??
roosetr what type of honda make modle and ecmre you rworking with ?
roosetr what type of honda make modle and ecmre you rworking with ?
Thread
Thread Starter
Forum
Replies
Last Post