holley commander 950
#1
Junior Member
Thread Starter
iTrader: (4)
Join Date: Jan 2009
Location: Owensboro, Ky
Posts: 63
Likes: 0
Received 1 Like
on
1 Post
Car: 1992 WS6 T/A
Engine: Turbo 383 with Holley Sniper
Transmission: factory 5 speed now Powerglide
Axle/Gears: Strange 12 bolt w/373 locker
holley commander 950
quick story, 92 5 speed 305tpi trans am. 166000 miles when a rod started knocking. putting a built 383 in it. thought i wsa gonna go carb so i CAREFULLY pulled out the harness from the ecu to the c100 plug. changed my mind and bought a holley commander 950 and a single plan efi setup. i have never messed with anything fuel injected before so im still learning. do i use my stock harness and do away with the stock ecm? anything i should know before i start putting this setup in?
#2
Member
iTrader: (9)
Join Date: Feb 2009
Location: Nowthen, MN
Posts: 323
Likes: 0
Received 2 Likes
on
2 Posts
Car: 87 monte aerocoupe
Engine: 383 HSR w/ novi 2000
Transmission: Built 4l80e circle d converter
Axle/Gears: Currie 9" 3.89 gears
Re: holley commander 950
The c950 has a different wiring harness than the stock one. I have heard of people rewiring the c950 harness to the factory harness, but it does take time. You would also need to make sure the sensor readings are the same as what the c950 needs to operate.
#3
Junior Member
Thread Starter
iTrader: (4)
Join Date: Jan 2009
Location: Owensboro, Ky
Posts: 63
Likes: 0
Received 1 Like
on
1 Post
Car: 1992 WS6 T/A
Engine: Turbo 383 with Holley Sniper
Transmission: factory 5 speed now Powerglide
Axle/Gears: Strange 12 bolt w/373 locker
Re: holley commander 950
ive always heard that the c950 is a direct replacement for the stock one.
#4
Supreme Member
iTrader: (33)
Join Date: Jul 2000
Location: Boosted Land
Posts: 5,945
Likes: 0
Received 1 Like
on
1 Post
Car: 92 Z28
Engine: Boosted LSX
Re: holley commander 950
repin the stock harness to work with the c950.
Did you get a book with the c950? if so it has all the wiring diagrams needed..
Did you get a book with the c950? if so it has all the wiring diagrams needed..
#5
Junior Member
Thread Starter
iTrader: (4)
Join Date: Jan 2009
Location: Owensboro, Ky
Posts: 63
Likes: 0
Received 1 Like
on
1 Post
Car: 1992 WS6 T/A
Engine: Turbo 383 with Holley Sniper
Transmission: factory 5 speed now Powerglide
Axle/Gears: Strange 12 bolt w/373 locker
Re: holley commander 950
Yeah i've got the book. Haven't really had time to fully read it but I have an electric speedo that runs through the stock ecm. Will it still work with the 950?
#7
Supreme Member
iTrader: (1)
Join Date: Nov 2003
Location: Davenport, Iowa
Posts: 1,598
Likes: 0
Received 2 Likes
on
2 Posts
Car: Still a 3rd Gen
Engine: 450HP 355
Transmission: TH350
Axle/Gears: 9" with 4.11's
Re: holley commander 950
You have to swap a few wires around in the connectors but it's not too bad. I wired one to work on a '7730 harness and it took a few hours.
Trending Topics
#8
Junior Member
Thread Starter
iTrader: (4)
Join Date: Jan 2009
Location: Owensboro, Ky
Posts: 63
Likes: 0
Received 1 Like
on
1 Post
Car: 1992 WS6 T/A
Engine: Turbo 383 with Holley Sniper
Transmission: factory 5 speed now Powerglide
Axle/Gears: Strange 12 bolt w/373 locker
Re: holley commander 950
u wouldnt happen to know which wires u switched do you?
#9
Supreme Member
iTrader: (1)
Join Date: Nov 2003
Location: Davenport, Iowa
Posts: 1,598
Likes: 0
Received 2 Likes
on
2 Posts
Car: Still a 3rd Gen
Engine: 450HP 355
Transmission: TH350
Axle/Gears: 9" with 4.11's
Re: holley commander 950
It's been quite a while but it's pretty easy to figure them out. All you need is the diagram for the 950 and the diagram for your car.
One good option is to pick up a spare harness from the junk yard and modify that one just in case you ever need to go back.. or pick up a Holley harness.
One good option is to pick up a spare harness from the junk yard and modify that one just in case you ever need to go back.. or pick up a Holley harness.
#10
Supreme Member
iTrader: (33)
Join Date: Jul 2000
Location: Boosted Land
Posts: 5,945
Likes: 0
Received 1 Like
on
1 Post
Car: 92 Z28
Engine: Boosted LSX
Re: holley commander 950
You have the 950C book. It has everything in there. All diagrams needed. (atleast mine does) you can also find the 7730 harness info on this site.
label everything 1st. Then depin it. and repin it. Like said above start to finish only takes a few hrs.
label everything 1st. Then depin it. and repin it. Like said above start to finish only takes a few hrs.
#11
Junior Member
Thread Starter
iTrader: (4)
Join Date: Jan 2009
Location: Owensboro, Ky
Posts: 63
Likes: 0
Received 1 Like
on
1 Post
Car: 1992 WS6 T/A
Engine: Turbo 383 with Holley Sniper
Transmission: factory 5 speed now Powerglide
Axle/Gears: Strange 12 bolt w/373 locker
Re: holley commander 950
10 4 ill give it a shot. Thanks for the info.
Thread
Thread Starter
Forum
Replies
Last Post
RedLeader289
Tech / General Engine
10
05-28-2019 01:47 PM
Royal_Z
Engine/Drivetrain/Suspension Parts for Sale
4
09-30-2015 08:45 PM