Well, this isn't good...
#1
Moderator
Thread Starter
Well, this isn't good...
I just had a Q-Jet returned to me for leaking fuel. The main metering well plugs were leaking, which is not at all unusual. The disturbing part is that I had recently rebuilt it, and epoxied over the main and secondary well plugs. No, I didn't miss, but the fuel dissolved the epoxy. I'm guessing it may have something to do with the ethanol and/or fuel additives, since this is the same epoxy I've been using forever (Conap E-Z-Poxy) and it has always survived heat and fuel.
What are you all using to seal against fuel? The epoxy I applied had turned clear, then to a goo, It's still in a gelled state, and had even dripped onto the gasket/spacer and was soft enough to wipe off with a cloth. I know it was cured when I assembled it. Beware!
What are you all using to seal against fuel? The epoxy I applied had turned clear, then to a goo, It's still in a gelled state, and had even dripped onto the gasket/spacer and was soft enough to wipe off with a cloth. I know it was cured when I assembled it. Beware!
#3
Moderator
Thread Starter
The Q-Jet was replacing a Holley. The Holley replaced an Edelbrock AFB. The AFB dogged at low RPM (14" Hg. vacuum). The Holley wouldn't idle despite several metering changes. It ran best by far with the Rochester until the plug leaks started fattening up the idle. Looks like I'm still hunting for a new type epoxy.
#4
Supreme Member
iTrader: (1)
Join Date: Jul 2004
Location: Calgary, AB, Canada
Posts: 10,763
Likes: 0
Received 4 Likes
on
4 Posts
Car: 1982 Trans-Am
Engine: 355 w/ ported 416s
Transmission: T10, hurst shifter
Axle/Gears: 10 bolt, true-trac, 3.73
what about edelbrocks epoxy? they claim it's fuel resistant, and i'm guessing of all companies that would actually test that, edelbrock would be one..
#7
Member
Join Date: Apr 2004
Posts: 436
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1987 TA
Engine: 350 stock/twecked
Transmission: 700r4
hello
how much fuel presure are you using? I would sugest a regulator just incase your fuel pump is spiking on you? I would try that elderbrock epoxy like stated before . I talked to the guy who dose carbs in this aera and he said that he dose not use epoxy--I guess to each his own
later and
GB
rk
It ran best by far with the Rochester until the plug leaks started fattening up the idle. Looks like I'm still hunting for a new type epoxy.
later and
GB
rk
Trending Topics
#8
Moderator
iTrader: (14)
Join Date: Mar 2000
Location: Littleton, CO USA
Posts: 43,169
Likes: 0
Received 36 Likes
on
34 Posts
Car: 82 Berlinetta/57 Bel Air
Engine: LS1/LQ4
Transmission: 4L60E/4L80E
Axle/Gears: 12B-3.73/9"-3.89
The only "pressures" that affects the well plugs are the delta-pressure between the manifold and atmosphere, and the fuel column height - i.e., gravity.
I've used JB Weld with 10% ethanol with no problems, but I don't know about some of the latest stuff out there.
I've used JB Weld with 10% ethanol with no problems, but I don't know about some of the latest stuff out there.
#9
Moderator
Thread Starter
I think I many have found a suitable replacement. The package claims fuel and additive resistance. I've got about 50/50 gasoline and ethanol soaking in the bowl now (yes, the brass float has been changed out for plastic).
The old epoxy just let go:
The old epoxy just let go:
#12
Supreme Member
Join Date: Jan 2002
Location: California
Posts: 1,162
Likes: 0
Received 1 Like
on
1 Post
Car: Z28
Engine: L98
Transmission: T56
while I don't doubt that changing fuel mixtures are are a very likely culprit, you may still want to mix up a another batch of your old reliable epoxy and do a test just to see if it dissolves again. this could rule out any inconsistenty in the mixture of the plugs that did dissolve (maybe that batch didn't get enough hardner or resin?)
#13
Moderator
Thread Starter
I think you've identified the problem. The old Conap has always worked well. I either didn't mix correctly or the shelf life has long since passed. I used a different product and soaked it in 50-50 ethanol/gasoline and had no softening.
I think perhaps the original coat of epoxy never fully cured. Either way, the problem is solved.
I think perhaps the original coat of epoxy never fully cured. Either way, the problem is solved.
Thread
Thread Starter
Forum
Replies
Last Post