Body Side Molding
#1
Thread Starter
Member
Joined: Oct 2018
Posts: 243
Likes: 171
From: Ft Wayne, IN
Car: 1987 Iroc Conv/90 Iroc Conv
Engine: LB9/LB9
Transmission: MM5/Auto
Body Side Molding
Looking for a set of body side door moldings. If anyone out there would have a set, color does not matter as I will be painting them to match the car. PM me if you have anything available. Thank you in advance.
#2
Senior Member
Joined: Oct 2021
Posts: 561
Likes: 80
From: Windsor, On
Car: 1984 Trans AM
Engine: 305
Transmission: 700-4r
Axle/Gears: 3.23
Re: Body Side Molding
My 1984 Trans AM has the factory mounted body sire mouldings which are colour keyed. U hardly know they are present as they blend right in.
Decades ago, I installed the aftermarket body side mouldings on my 1970 Chevelle. Real door ding savers.
U could purchase aftermarket set & have them installed. I would do that.
Decades ago, I installed the aftermarket body side mouldings on my 1970 Chevelle. Real door ding savers.
U could purchase aftermarket set & have them installed. I would do that.
#3
Joined: May 2008
Posts: 1,356
Likes: 51
From: Alabama
Car: 87 GTA
Engine: 5.7 TPI
Transmission: 700r4
Axle/Gears: 3:27 BW 9 bolt
Re: Body Side Molding
You can buy the 87-92 style that comes in two rolls (82-86 are different). They do have to be cut. I've still got a set, but I'll be using them eventually when I have my car repainted.
The following users liked this post:
IROCIN (09-07-2024)
The following users liked this post:
IROCIN (09-07-2024)
#5
Thread Starter
Member
Joined: Oct 2018
Posts: 243
Likes: 171
From: Ft Wayne, IN
Car: 1987 Iroc Conv/90 Iroc Conv
Engine: LB9/LB9
Transmission: MM5/Auto
#6
Joined: Sep 2007
Posts: 1,290
Likes: 43
From: Fayette County, OH
Car: basic third gens
Engine: that I like
Transmission: to restore
Axle/Gears: and enjoy
Re: Body Side Molding
Are you looking for a full 6pc set, or just the long ones for the doors? I believe I still have a couple sets of good used ones. But I'm currently out of town and can't double check.
The following users liked this post:
IROCIN (10-12-2024)
#7
Thread Starter
Member
Joined: Oct 2018
Posts: 243
Likes: 171
From: Ft Wayne, IN
Car: 1987 Iroc Conv/90 Iroc Conv
Engine: LB9/LB9
Transmission: MM5/Auto
Re: Body Side Molding
Thank you for the offer. I was able to get the full 6 piece set (used) from a guy up in Michigan, so I should be set.
The following 3 users liked this post by IROCIN:
86blackiroc (Yesterday), chazman (10-12-2024)
Trending Topics
#8
Senior Member
Joined: Oct 2021
Posts: 561
Likes: 80
From: Windsor, On
Car: 1984 Trans AM
Engine: 305
Transmission: 700-4r
Axle/Gears: 3.23
Re: Body Side Molding
The following users liked this post:
IROCIN (Yesterday)
#10
Senior Member
Joined: Oct 2021
Posts: 561
Likes: 80
From: Windsor, On
Car: 1984 Trans AM
Engine: 305
Transmission: 700-4r
Axle/Gears: 3.23
Thread
Thread Starter
Forum
Replies
Last Post