Evoluzione panel joint ideas
#1
Senior Member
Thread Starter
iTrader: (8)
Join Date: Jul 2006
Location: Davisburg, MI
Posts: 683
Likes: 0
Received 1 Like
on
1 Post
Car: 87 Evoluzione, 84 TransAm, 05 GTO
Engine: LT1, L98, LS2
Transmission: (2) T56 & (1) 700R4
Axle/Gears: Moser 12-bolt w/3.73 & Stock
Evoluzione panel joint ideas
Getting back to my Evoluzione project. I have a butt joint where the front fender is supposed to mold into the rocker. I had to cut this apart when I installed my vertical doors. Seems I should keep this removable for service. My first thought was finishing the edges and with a bracket behind the rocker have 3 or 4 visible dzus 1/4 turn fasteners visible on each side. Anybody got any better ideas?
#2
Banned
iTrader: (12)
Join Date: Jul 1999
Location: Bertram (outside Austin), TX
Posts: 12,212
Likes: 0
Received 10 Likes
on
10 Posts
Car: 87 GTA
Engine: L98
Transmission: 700R4
Axle/Gears: Dana M78 3.27 posi
Re: Evoluzione panel joint ideas
Pics of what your talking about? But it sounds similar to what I've seen on a Pro Street 55 Chevy. The rear tires were tucked so high up, even when jacked up, the tops of the tires were still in the fenders.
So he made part of the side of the quarter removable.
So he made part of the side of the quarter removable.
Last edited by Stephen; 11-21-2008 at 09:30 AM. Reason: typo
#3
Senior Member
iTrader: (4)
Join Date: Jan 2008
Location: Rustfree Gilbert Arizona
Posts: 545
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1989 IROC
Engine: 305TPI
Transmission: 700R4
Axle/Gears: 2:73 posi
Re: Evoluzione panel joint ideas
I think you should keep it smooth. I know what your saying but the only reason I can think of to service it would be for the antenna. Unless you get hit.......
#4
Senior Member
Thread Starter
iTrader: (8)
Join Date: Jul 2006
Location: Davisburg, MI
Posts: 683
Likes: 0
Received 1 Like
on
1 Post
Car: 87 Evoluzione, 84 TransAm, 05 GTO
Engine: LT1, L98, LS2
Transmission: (2) T56 & (1) 700R4
Axle/Gears: Moser 12-bolt w/3.73 & Stock
Re: Evoluzione panel joint ideas
I'm worried about servicing the lift struts hinge adjustments.
#6
Senior Member
Thread Starter
iTrader: (8)
Join Date: Jul 2006
Location: Davisburg, MI
Posts: 683
Likes: 0
Received 1 Like
on
1 Post
Car: 87 Evoluzione, 84 TransAm, 05 GTO
Engine: LT1, L98, LS2
Transmission: (2) T56 & (1) 700R4
Axle/Gears: Moser 12-bolt w/3.73 & Stock
Re: Evoluzione panel joint ideas
I like that idea. Simple L-brackets behind the panel and I'd be able to adjust the alignment easily.
#7
Member
Join Date: Oct 2004
Location: ohio
Posts: 379
Likes: 0
Received 0 Likes
on
0 Posts
Car: 88IROC vert and a 83 w/evo body
Engine: 400 and 350
Transmission: T56 and 700R4
Axle/Gears: 323 and 373
Re: Evoluzione panel joint ideas
What UDAMON said. From what Iv'e heard about these doors they are always needing readjusted.
Trending Topics
#10
Member
Join Date: Oct 2004
Location: ohio
Posts: 379
Likes: 0
Received 0 Likes
on
0 Posts
Car: 88IROC vert and a 83 w/evo body
Engine: 400 and 350
Transmission: T56 and 700R4
Axle/Gears: 323 and 373
Re: Evoluzione panel joint ideas
Very nice. You should do the same thing to the rear quarter part. Mine cracked back their from jacking up the car stressed this point over a period of time and cracked the part that you mold together. What you done with the front part would look nice bark there and match the front.
#11
Senior Member
Thread Starter
iTrader: (8)
Join Date: Jul 2006
Location: Davisburg, MI
Posts: 683
Likes: 0
Received 1 Like
on
1 Post
Car: 87 Evoluzione, 84 TransAm, 05 GTO
Engine: LT1, L98, LS2
Transmission: (2) T56 & (1) 700R4
Axle/Gears: Moser 12-bolt w/3.73 & Stock
Re: Evoluzione panel joint ideas
Man, you don't want me to ever finish this car!
My passenger side split along the rear of the rocker I thought because I bumped my hoist backing in without mirrors. The LH side I noticed 2 nights ago a tiny hairline crack. I was thinking I had too much material in the joint and was going to redo it. Based on your input I'll add flanging it the same as the front to my list. Thanks for the input.
My passenger side split along the rear of the rocker I thought because I bumped my hoist backing in without mirrors. The LH side I noticed 2 nights ago a tiny hairline crack. I was thinking I had too much material in the joint and was going to redo it. Based on your input I'll add flanging it the same as the front to my list. Thanks for the input.
#12
Member
Join Date: Sep 2008
Location: Concord, NC
Posts: 164
Likes: 0
Received 0 Likes
on
0 Posts
Car: 89 Camaro, 94 z-71,98 Camaro
Engine: none, 350 tbi.sixxer
Transmission: none, 4l60e,auto
Axle/Gears: none, 3.73
Re: Evoluzione panel joint ideas
I agree on the brackets on the backside ...it does look good. As far as finishing our cars...... ARE WE EVER FINISHED? LOL
#13
Member
Join Date: Oct 2004
Location: ohio
Posts: 379
Likes: 0
Received 0 Likes
on
0 Posts
Car: 88IROC vert and a 83 w/evo body
Engine: 400 and 350
Transmission: T56 and 700R4
Axle/Gears: 323 and 373
Re: Evoluzione panel joint ideas
Nope, never finished. Even when everyone thinks it's done, back in the garage we go. Also the longer it takes everyone to finish theirs the more rare mine is complete.
Thread
Thread Starter
Forum
Replies
Last Post