Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LSX!)
#1851
Senior Member
Thread Starter
Join Date: Jul 1999
Location: Houston, TX
Posts: 888
Likes: 0
Received 0 Likes
on
0 Posts
Car: '87+'02 Z28
Engine: 454 LSX
Transmission: T-56, Viper output shaft
Axle/Gears: Strage 12-bolt 3.73:1
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
Hey guys, well I will have new video when I get the brake lights assembled and functioning. Today I finally recevied the smoked red and smoked clear (reverse) lenses from KLEARZ. Let me tell you, this guys stuff is quality and very well done! I will post pics this weekend as I start getting the LED boards from Spaghetti Engineering positioned and installed in the housings AND get the lenses laid out as well. Since my brake light housings were modified by the body shop I will have to build-up the back of both housings to strengthen them a bit (the pics will show you where I am talking about).
Once the brake lights are working, i'll then hopefully have the car over to John's shop (American Race Components) to fabricate the cold/ram air induction system with air filter box and also strut tower brace, radiator fan shroud and other little odds and ends. Then, i'll get this thing out on the street and have some video for you
Once the brake lights are working, i'll then hopefully have the car over to John's shop (American Race Components) to fabricate the cold/ram air induction system with air filter box and also strut tower brace, radiator fan shroud and other little odds and ends. Then, i'll get this thing out on the street and have some video for you
#1852
Member
iTrader: (2)
Join Date: Feb 2008
Location: Conroe, TX
Posts: 294
Likes: 0
Received 0 Likes
on
0 Posts
Car: '70 Bronco, '91 Firebird, '03 Chevy
Engine: roller 302, 350 TB, stock 6.0
Transmission: NP435 Granny 4 spd, 700R4, 4L80E
Axle/Gears: 4.56 spool, 2.73 open, 4.10 broken
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
#1853
Senior Member
Join Date: Jun 2008
Location: Norfolk VA
Posts: 1,298
Likes: 0
Received 2 Likes
on
2 Posts
Car: 85 Camaro IROC
Engine: 5.7 TPI
Transmission: 700-R4
Axle/Gears: open rear, 3.42 gears
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
Originally Posted by 1bad91Z
asking someone exactly how much money they have in their car is like asking someone how big are his wife's ****. It's kind of personal.
just trust that he has enough in it to make it the car of his dreams
thats all that really matters in the end.
the only reason to ask is if you were planning to buy it from him, and it kinda like, if you have to ask... you cant afford it
neil,
one thing i am not sure about is using the spaghetti engineering LED bulb kit
if you have the time, you would be much better off to make your own.
not totally dissing their product, but on a un-modified camaro they look decent... on yours, it would be like a two yr old coming over to do your pin striping with a crayola crayon.
you could at least send the lenses to someone who could do a custom job and be miles ahead in quality IMO
oh, and c-mon man, lets see some vids
ill even GIVE YOU MY CAMERA if thats what it takes...
jk but seriously, great looking car.
Last edited by RED_DRAGON_85; 11-03-2009 at 08:17 AM.
#1854
Member
Join Date: Sep 2006
Location: Syracuse, UT
Posts: 170
Likes: 0
Received 1 Like
on
1 Post
Car: 1991 Vert Z28
Engine: 305... LS1 waiting to drop in
Transmission: 700-R4... soon 4L60E
Axle/Gears: 3.08 posi nine bolt
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
Oh man 1853 posts and no driving videos? This car is very very cool!
#1855
Member
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
What's the latest...need an update, PLEASE!
#1856
TGO Supporter
Join Date: Nov 2002
Location: Puerto Rico
Posts: 316
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1988 IROC Convertible
Engine: 305 TPI
Transmission: Auto
#1857
Supreme Member
iTrader: (7)
Join Date: Aug 2005
Location: Ohio, near columbus
Posts: 1,068
Likes: 0
Received 1 Like
on
1 Post
Car: 89 iroc-z
Engine: 305tpi
Transmission: wc-t5
Axle/Gears: 10 bolt 3.08 posi (4 now)
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
kool car possibly the most modified thirdgen, i've ever seen! Beautiful, should be a lot of fun.
i now have to go pay attention to my girl as i've spent the past 3 nights reading almost this entire 38 pages word for word. beautiful product. i hope to someday perfect my skills enough to do work like that entirely by myself ,but someday is a long way aways for sure.
i now have to go pay attention to my girl as i've spent the past 3 nights reading almost this entire 38 pages word for word. beautiful product. i hope to someday perfect my skills enough to do work like that entirely by myself ,but someday is a long way aways for sure.
#1859
Junior Member
Join Date: Aug 2008
Location: Kansas City Metro Area
Posts: 34
Received 0 Likes
on
0 Posts
Car: 1985 Z28/ IROC-Z
Engine: 5.0 TPI
Transmission: 700R4
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
Looks like http://dev.cwihosting.com/suspended....umName=album03 is down too... so I cant even oogle and ahhhh over it anymore... bummer
#1860
Member
Join Date: Aug 2009
Location: Colorado Springs, CO and Billings, MT
Posts: 140
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Z28
Engine: 305 TPI
Transmission: 700R4
Axle/Gears: 2.73
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
well i just finished reading this.... yes all the way to post #1859... my eyes are bleeding and I am going to bed now.. But all I can say is holy $#!# is your car sweet!!!! Haha it will take a miracle for me to not dream of driving your car tonight...
#1861
Senior Member
Join Date: Jun 2008
Location: Norfolk VA
Posts: 1,298
Likes: 0
Received 2 Likes
on
2 Posts
Car: 85 Camaro IROC
Engine: 5.7 TPI
Transmission: 700-R4
Axle/Gears: open rear, 3.42 gears
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
wow... its been a while.
any idea what happened to this car?
did neil have to go into the sexy car protection program?
any idea what happened to this car?
did neil have to go into the sexy car protection program?
#1863
Junior Member
Join Date: Jan 2009
Location: Victoria, B.C. (thats Canada)
Posts: 84
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Camaro RS
Engine: 305 TBI
Transmission: WC T-5 (slushbox)
Axle/Gears: 3.08
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
Man this is incredible, the only things that I can think of that are still stock (off the top of my head) on this car is the frame, spindles, SOME body panels and the carpet! LOL
Oh and i guess the t-tops aswell
Great work Neil, beautiful car
Oh and i guess the t-tops aswell
Great work Neil, beautiful car
#1864
Senior Member
Thread Starter
Join Date: Jul 1999
Location: Houston, TX
Posts: 888
Likes: 0
Received 0 Likes
on
0 Posts
Car: '87+'02 Z28
Engine: 454 LSX
Transmission: T-56, Viper output shaft
Axle/Gears: Strage 12-bolt 3.73:1
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
Hey guys, I am still around and not in the "sexy car protection program" LMAO!!! I plan on taking a few photos and posting in a few days. Having the air box (air filter) system fabricated, custom strut tower brace (the BMR STB I purchase won't work with this intake) and also rad fan shroud.
I have been soooo busy at work, so i'll update you guys shortly!
I have been soooo busy at work, so i'll update you guys shortly!
#1867
Supreme Member
iTrader: (1)
Join Date: Jul 2001
Location: Houston Area
Posts: 4,627
Likes: 0
Received 3 Likes
on
2 Posts
Car: Faster
Engine: Than
Transmission: You!
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
My wife has 36 triple D's. I don't mind sharing,lol
#1868
#1870
Supreme Member
iTrader: (1)
Join Date: Jul 2001
Location: Houston Area
Posts: 4,627
Likes: 0
Received 3 Likes
on
2 Posts
Car: Faster
Engine: Than
Transmission: You!
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
Well post a slightly covered pic of them, I mean her in front of your thirdgen!
#1871
Senior Member
Thread Starter
Join Date: Jul 1999
Location: Houston, TX
Posts: 888
Likes: 0
Received 0 Likes
on
0 Posts
Car: '87+'02 Z28
Engine: 454 LSX
Transmission: T-56, Viper output shaft
Axle/Gears: Strage 12-bolt 3.73:1
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
Hey, even a piece of tape counts as clothing!
#1872
Supreme Member
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
You guys are perverts! But seriously, where's the picture?
#1874
Supreme Member
#1877
Senior Member
iTrader: (1)
Join Date: Sep 2006
Location: Canada
Posts: 962
Likes: 0
Received 13 Likes
on
10 Posts
Car: 1979 Malibu
Engine: Blown LSx
Transmission: T56 Magnum
Axle/Gears: 9"/wavetrac/35's/3.70
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
Neil, I BEG of you in all that is good in the world of camaros to please update, i will paypal you 7.00$ can funds to update PLEASE!
#1878
Senior Member
Thread Starter
Join Date: Jul 1999
Location: Houston, TX
Posts: 888
Likes: 0
Received 0 Likes
on
0 Posts
Car: '87+'02 Z28
Engine: 454 LSX
Transmission: T-56, Viper output shaft
Axle/Gears: Strage 12-bolt 3.73:1
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
Sorry to keep you guys waiting so long, but now have updated pics of the recent additions
First, the custom/super-tight-fit strut tower brace has finally taken shape. Rod ends bolt into each strut tower and each of the welded-in ends on each strut tower will be gusseted to increase strength (not gusseted in pics). Also, on each end of the STB, smaller supports will bolt into the frame rails to tie in the front end and make it pretty tight structurally.
First, the custom/super-tight-fit strut tower brace has finally taken shape. Rod ends bolt into each strut tower and each of the welded-in ends on each strut tower will be gusseted to increase strength (not gusseted in pics). Also, on each end of the STB, smaller supports will bolt into the frame rails to tie in the front end and make it pretty tight structurally.
#1879
Senior Member
Thread Starter
Join Date: Jul 1999
Location: Houston, TX
Posts: 888
Likes: 0
Received 0 Likes
on
0 Posts
Car: '87+'02 Z28
Engine: 454 LSX
Transmission: T-56, Viper output shaft
Axle/Gears: Strage 12-bolt 3.73:1
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
Here are pics of the vertical supports connecting the frame rails to the STB.
The last pic in this series is of the new timing mark pointer which replaced my filed down bolt. My fabbed timing pointer obvioulsy sucks in comparison to the one John made.
The last pic in this series is of the new timing mark pointer which replaced my filed down bolt. My fabbed timing pointer obvioulsy sucks in comparison to the one John made.
#1880
Senior Member
Thread Starter
Join Date: Jul 1999
Location: Houston, TX
Posts: 888
Likes: 0
Received 0 Likes
on
0 Posts
Car: '87+'02 Z28
Engine: 454 LSX
Transmission: T-56, Viper output shaft
Axle/Gears: Strage 12-bolt 3.73:1
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
The pics below are of the relocated coli brackets which John actually made 1st, since my car has been back at his shop. These brackets will have a cover to sheild the coils from radiant header/engine heat and the spark plug wires will now run under the headers for a nice clean look So, now I have to buy another set of universal Taylor wires to cut to length. Also, I can now remove the coil relocation brackets from the valve covers, which are awesome in construction and design, but they cover up too much of my intake, so they are coming off and will sell them along with the wires.
#1881
Senior Member
Thread Starter
Join Date: Jul 1999
Location: Houston, TX
Posts: 888
Likes: 0
Received 0 Likes
on
0 Posts
Car: '87+'02 Z28
Engine: 454 LSX
Transmission: T-56, Viper output shaft
Axle/Gears: Strage 12-bolt 3.73:1
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
Now the biggest and most important piece, the air filter box plenum or airbox, however you want to call it. The big dilemma here was to get dual 3" pipes and the airbox plenum to fit under the hood. After a while of head scatching the choices made were to cut out the upper and lower radiator supports and fab new ones which lowered the radiator approx. 3.5" thus allowing more room for the airbox and tubes to the throttle body. After all this work, the plenum still hits the underside of the hood, so the hood has to be cut and will out an area large enough to clear the airbox setup as well as cut completely through the hood in front of the fake intake vent. The plan is to have clear lexan cover that area in front of the hood "vent" which would expose the tubes to the throttle body.
These pics show the mock up using card board where the airfilters will approximately be. The air filter dimensions for each filter are 7.6" x 12.8" and provide a total filter area of approximately 160 sq. in. The recommended filter area for this engine setup is 152 sq. in. so we are good to go.
These pics show the mock up using card board where the airfilters will approximately be. The air filter dimensions for each filter are 7.6" x 12.8" and provide a total filter area of approximately 160 sq. in. The recommended filter area for this engine setup is 152 sq. in. so we are good to go.
#1882
Senior Member
Thread Starter
Join Date: Jul 1999
Location: Houston, TX
Posts: 888
Likes: 0
Received 0 Likes
on
0 Posts
Car: '87+'02 Z28
Engine: 454 LSX
Transmission: T-56, Viper output shaft
Axle/Gears: Strage 12-bolt 3.73:1
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
Now, using aluminum, John is mocking up pieces to see how everything would fit and to see the clearance when the hood is closed. The plastic bumper/front end support had to be removed in areas to allow for clearance of the filter housing
#1883
Senior Member
Thread Starter
Join Date: Jul 1999
Location: Houston, TX
Posts: 888
Likes: 0
Received 0 Likes
on
0 Posts
Car: '87+'02 Z28
Engine: 454 LSX
Transmission: T-56, Viper output shaft
Axle/Gears: Strage 12-bolt 3.73:1
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
Now, the filters in place and an aluminum mock up of the top plenum piece.
#1884
Senior Member
Thread Starter
Join Date: Jul 1999
Location: Houston, TX
Posts: 888
Likes: 0
Received 0 Likes
on
0 Posts
Car: '87+'02 Z28
Engine: 454 LSX
Transmission: T-56, Viper output shaft
Axle/Gears: Strage 12-bolt 3.73:1
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
More of the airbox mock up inside and out.
I have had trouble finding a silicone coupler for the throttle body with an internal diameter of 5.75", not being able to find it in silicone, I will try to use a 5.62" internal dia rubber hose and see if it will stretch over the TB.
I have had trouble finding a silicone coupler for the throttle body with an internal diameter of 5.75", not being able to find it in silicone, I will try to use a 5.62" internal dia rubber hose and see if it will stretch over the TB.
#1885
Senior Member
Thread Starter
Join Date: Jul 1999
Location: Houston, TX
Posts: 888
Likes: 0
Received 0 Likes
on
0 Posts
Car: '87+'02 Z28
Engine: 454 LSX
Transmission: T-56, Viper output shaft
Axle/Gears: Strage 12-bolt 3.73:1
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
Another pic of what will be the inside area of the air box plenum and a section of the hood which has already been cut out and more will be cut once the airbox is all setup up.
Last edited by Neil; 01-03-2010 at 06:10 PM.
#1886
Member
iTrader: (2)
Join Date: Jul 2008
Location: near chicago illinois
Posts: 475
Likes: 0
Received 0 Likes
on
0 Posts
Car: have a 92 camaro rs...in pieces
Engine: none now...probably 383 stroker
Transmission: none yet
Axle/Gears: none
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
That's sick man.. Wish i had your skills... Good job. Keep it up.
#1887
Senior Member
Thread Starter
Join Date: Jul 1999
Location: Houston, TX
Posts: 888
Likes: 0
Received 0 Likes
on
0 Posts
Car: '87+'02 Z28
Engine: 454 LSX
Transmission: T-56, Viper output shaft
Axle/Gears: Strage 12-bolt 3.73:1
#1890
Senior Member
Join Date: Aug 2009
Location: Thunder Bay, On, Canada
Posts: 289
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1985 Camaro
Engine: 2.8l
Transmission: 700r4
Axle/Gears: Stock
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
Wow, Almost 4 years into it. I checked out the last 8 pages and it looks sickk. The intake looks cool. I wonder how well it's going to work. I haven't seen anything like that before. Good job
#1892
Senior Member
Thread Starter
Join Date: Jul 1999
Location: Houston, TX
Posts: 888
Likes: 0
Received 0 Likes
on
0 Posts
Car: '87+'02 Z28
Engine: 454 LSX
Transmission: T-56, Viper output shaft
Axle/Gears: Strage 12-bolt 3.73:1
#1893
Senior Member
Thread Starter
Join Date: Jul 1999
Location: Houston, TX
Posts: 888
Likes: 0
Received 0 Likes
on
0 Posts
Car: '87+'02 Z28
Engine: 454 LSX
Transmission: T-56, Viper output shaft
Axle/Gears: Strage 12-bolt 3.73:1
#1895
Supreme Member
iTrader: (3)
Join Date: Jan 2004
Location: p'cola FL
Posts: 2,311
Likes: 0
Received 0 Likes
on
0 Posts
Car: 88 iroc-z/28
Engine: 408 lsx
Transmission: 5800 stall
Axle/Gears: 4.71
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
that is one heck of a strut brace. very well fabbed and good mounting points.
how hard is it to get on and off?
pics are deceiving.
are those TWO ls1 style filters?
crazy man. lookin damn near perfect.
how hard is it to get on and off?
pics are deceiving.
are those TWO ls1 style filters?
crazy man. lookin damn near perfect.
#1896
On Probation
iTrader: (9)
Join Date: Feb 2005
Location: So Cal
Posts: 2,042
Likes: 0
Received 2 Likes
on
2 Posts
Car: 87 IROC-Z
Engine: LsX
Transmission: MN12 6speed
Axle/Gears: 3:42
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
how did i miss these last 2 pages..
#1897
Senior Member
Thread Starter
Join Date: Jul 1999
Location: Houston, TX
Posts: 888
Likes: 0
Received 0 Likes
on
0 Posts
Car: '87+'02 Z28
Engine: 454 LSX
Transmission: T-56, Viper output shaft
Axle/Gears: Strage 12-bolt 3.73:1
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
Well, with a little twisting the STB should slide out fairly easily. The air filter is actually from a Pontiac Grand Am and as you can see I am using two
#1898
Senior Member
iTrader: (1)
Join Date: Jul 1999
Location: New York City
Posts: 503
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 IROC
Engine: 355 Tpi
Transmission: 700r4
Axle/Gears: 9 Bolt 3.27
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
Such an awesome build Neil, I can't wait to see this thing in a magazine or if I'm really lucky in person.
#1899
Supreme Member
iTrader: (1)
Join Date: Jun 2001
Location: Tacoma, Wa
Posts: 3,109
Likes: 0
Received 25 Likes
on
17 Posts
Car: '91 TA vert
Engine: turboLSx
Transmission: T56
Axle/Gears: 3.23
Re: Phase I done, Phase II-interior almost done, and now Phase III-drivetrain (454 LS
Are those vertical supports indirectly going to prevent the fore-aft movement the strut towers see?
#1900
Senior Member
Thread Starter
Join Date: Jul 1999
Location: Houston, TX
Posts: 888
Likes: 0
Received 0 Likes
on
0 Posts
Car: '87+'02 Z28
Engine: 454 LSX
Transmission: T-56, Viper output shaft
Axle/Gears: Strage 12-bolt 3.73:1