VincentZ28

iTrader: (2)

What are some of your opinions about them. Here's mine!



It made 409whp at 6000.

Twin_Turbo

iTrader: (25)

Orr89RocZ

iTrader: (20)

my buddy's 94 TA with 406 miniram motor from his old 87 TA Old pic of first install but since then its been running well. 10.6's at 130mph all motor with a 6 speed. Miniram getting it done

92RS(real slow)

Any more specs on that engine I've been throwing around the idea of building a mini rammed 406

musicfreako

iTrader: (1)

Jealous!

Orr89RocZ

iTrader: (20)

Was a gm block, old AFR 195's that have been ported to 210 cc and flow ~310cfm, miniram i think ported to 1205 gasket, mid high 10's to 1 compression, was a TPIS 242/242 solid roller when it ran high 10's with auto trans, 11.0's with the T56, but now its a ultradyne custom grind, somewhere in the low 250's at .050 solid roller, mid 600's lift. Running off the 730 ecm.

T56 trans, i think 3.73 gears now, 28" tire. Spraying a 175 shot it went 9.88 at 142 with a slipping clutch

87_TA is the guy on this board. Its now a SHP block 406 with a single plane EFI intake, same heads/cam. T56 is getting rebuilt/faceplated since it broke so it hasnt run yet to its full potential with the new block/intake, but it made over 500whp I thought it was like 520's but I have to find the thread.

88BlackZ-51

iTrader: (2)

there really arent too many intakes out there for efi to put on a bigger stroker then a miniram.....

TTOP350

iTrader: (8)

my turd



When you get past the miniram call these guys..
http://www.hogansracingmanifolds.com/

86TA355SR

iTrader: (1)

Twin_Turbo: Is that car on You Tube? I saw a car like it earlier. Sick man, sick! Awesome ride!

Twin_Turbo

iTrader: (25)

Yes it's on Youtube. It's my buddies, I built most of it for him.

GTA matt

iTrader: (1)

Mine. After alot of polishing

sofakingdom

iTrader: (1)

Unfortunately the car and engine are missing.

thegooseman

LD85

iTrader: (2)

Street Lethal

iTrader: (16)

LD85, that is just pure sex! Beautiful engine....

LD85

iTrader: (2)

That was the prettiest engine I built of the 5 or so engines , the SR was 2nd.

Street Lethal

iTrader: (16)

LD85, I honestly can't get over how great the engine came out. Which paint did you use for the valve covers, and how durable would you say that it is....?

LD85

iTrader: (2)

On the Valve cover's Autozone Hi-Temp Red over wrinkle paint
On the intake Hi-temp Ceramic Silver, Autozone.

anesthes

iTrader: (12)

What heads?

-- Joe

gsmarcano

was gonna say about the same thing

Orr89RocZ

iTrader: (20)

Old non eliminator 195's that were ported out, I think hand finished to 210cc and flow 310cfm. Even the old 195's on the engine that were ported to flow 286cfm like the Eliminator series went high 10's on motor at 125-127 with a smaller cam!

anesthes

iTrader: (12)

See, this is my point in the other thread. A heavy 4th gen, with a 406, miniram, and smallish cam like you say and AFR 195 heads goes 127mph. We're talking over 600 flywheel horsepower.

I'm assuming the car was around 3700lbs with driver.

That's why I felt the power was down a bit on that 421.

I'm kinda psyched to see the SBC fit soo well with dizzy in the engine bay. It's gotten to the point where v6 4th gens are under $1500 all day with nice bodies, which would make a nice daily driver with a 350 + 700R4.


-- Joe

DAVECS1

iTrader: (2)

I want those valve covers so bad I do not even know how to express myself. Really wish they had a drooling happy face in here.

anesthes

iTrader: (12)

I used to have a miniram just like that.

-- Joe

Orr89RocZ

iTrader: (20)

Well it was a cleand up head, so it may have pushed more than 195cc, but it wasnt near that heavy. It was closer to 3400 lbs. 550hp-ish I think. Now the new setup with that 210cc head and bigger cam made 521whp through the 6 spd. Closer to 600 hp

GTA matt

iTrader: (1)

Hmmmmmm, that's wierd. lol

anesthes

iTrader: (12)

3400lbs? What was removed? I had two 4th gens, and they weighed a heck of a lot more than any of my third gens ( But not quite as much as my second gens) I think the firebird was around 3500 and the camaro a little more. PLUS driver.

-- Joe

GP406Z

here's one with better fuel rails

SuperRamFormula

iTrader: (1)

I c u made the switch from the superram to the miniram...do u think it was worth it? I'm thinking about swapping my superram system for a miniram or stealth ram. I saw in a earlier post your making more hp and lost some tq. What your overall opinion of the switch? Thx

Twin_Turbo

iTrader: (25)

me too, willing to pay top dollar too

VincentZ28

iTrader: (2)

It still needs more tuning. It was too rich from 3500 to 5000rpms. The A/F was reading 10.8-12.3 in that range due to too much pump shot. Next at the Dyno it will be corrected and the TQ will be higher. I swapped the Super Ram for the Miniram for free. I didn't have to pay for anything. So yea for me it was worth it.

Street Lethal

iTrader: (16)

Do you guys want me to hook you up with a link....?

Orr89RocZ

iTrader: (20)

IDK, i guess just interior but I have no idea. It has a full cage too and a big rear end. Its not uncommon for 4th gens to get down below 3400 tho. ALot of the record holder cars are in the 3000-3100 range

TTOP350

iTrader: (8)

Quote:
Originally Posted by DAVECS1
I want those valve covers so bad I do not even know how to express myself. Really wish they had a drooling happy face in here....

Quote:
Originally Posted by Twin_Turbo
me too, willing to pay top dollar too....

Thanx guys, I got my valve covers from GM

Street Lethal

iTrader: (16)

Yeah those valve covers are sweet! Here's a link, third set down....;

http://www.jrgmparts.com/GM_Performa..._small_bl.html

Twin_Turbo

iTrader: (25)

Summit says they are discontinued, as do other suppliers. A lot of sites still lsit them but I haven't found anyone that still has them. I only found a guy selling 1 cover

Street Lethal

iTrader: (16)

Some places still seem to have them stocked though....

http://www.karlperformanceparts.com/...?idproduct=244

TTOP350

iTrader: (8)

Guess I should say that Ive had them 4 prolly 10years or more

Twin_Turbo

iTrader: (25)

See, as I suspected..no longer available... TTOP, in a selling mood?

--------------------------------------------------------------------
Sorry, discontinued and no dealers nationwide show having any stock.
Thanks for checking with us!
--Adam

Adam Moore
Karl Chevrolet Inc.
Karl Performance Parts
Team Lead & Performance Parts Specialist

TTOP350

iTrader: (8)

lol Not today!! I have a guy doing some checking to see if any are around.
Did you check old Nascar team used parts places??

Twin_Turbo

iTrader: (25)

yeas, that's where I found 1. Terry Rosebush had only 1 cover, NIB. The other set I ound came with the pontiac racing heads, mucho $$$$$

TTOP350

iTrader: (8)

Hmm GM also used to sell the same covers but blank.
If those are still around, you could buy the 1 NIB cover, a blank one then CNC the Pontiac font in the blank..

Twin_Turbo

iTrader: (25)

The blank ones are still available. I had been thinking about that, having the pontiac script cut into them. Anyone have a DXF or so of the script?

TTOP350

iTrader: (8)

I havent looked forever but how much are the blank covers??

Twin_Turbo

iTrader: (25)

Looks like the blank ones are discontinues too... FFFFFFFFF!!!!!!!!!!!

I think they were something like 140 a pop, had to order 2 to get a set.

Looks like this guy wants 250 per cover
http://cgi.ebay.com/ebaymotors/GM-Pe...c#ht_534wt_939

A little bit much

TTOP350

iTrader: (8)

Wow Id say so! i paid 250ish for both of mine out the door from GM..

DAVECS1

iTrader: (2)

Did not realize this conversation fired back up :-) Yea I have looked everywhere for these. They are officially hens teeth. I even looked for the tool that was used to cast them. No luck. There are several places that will do custom CNC sets for a reasonable price but to me it just is not as convincing, for that OEM look. I was looking at getting a silicon sticker made with the pointiac exctement logo and putting it on an aluminum fab valve cover, best I could come up with.

FSTFBDY

iTrader: (33)

If you find the valve covers I could mill the logo in them kinda like the billet emblems I offer.
I can make a file of the pontiac script if I find a good picture of it.


Always loved the look of the mini ram.

QUICKCHICKEN

iTrader: (12)

2 ques, for you guys that have the factory serp setup, what did you do for clearance on the alt side where the lug is on the back side close to the valve cover?

my other ques is, whats this i was reading about the water neck issue?

SuperRamFormula

iTrader: (1)

Wow, pretty sweet deal! I have been watching ebay for a mini ram intake and was out bit twice. Are you using the stock ECM with a tune or a after market system? I'm thinking about just getting my accel superram base manifold ported, making a cam switch and possibly a Fast system.